基于2440的SPI测试驱动程序以及应用程序（实例）

在做项目时用到SPI所以这里整理了一下SPI的测试程序以便后用

下面是驱动部分：spi_ker.c

/********************************************
 *说明：本实验是针对TQ2440的SPI测试程序    *
 *设备模型：混杂设备                       *
 *内核选取：linux-2.6.32.2                 *
 *硬件要求：将MOSI与MISO短结               *
 *写作时间：2011/12/10                     *
 *编辑作者：Sheldon Chu                    *
********************************************/

#include
#include
#include
#include
#include
#include
#include
#include

int loopChar=0x11;
module_param(loopChar,int,S_IRUGO);

#define DEVICE_NAME "tq2440_spi"
static void __iomem *base_addr0;
static void __iomem *base_addr1;
static void __iomem *base_addr2;
static void __iomem *base_addr3;

//定义一个测试用的要发送的数据缓存包
static char *kbuf;
static int  kbuf_size;

#define S3C2440_CLKCON 0x4c00000c
#define S3C2440_GPG    0x56000060
#define S3C2440_GPE    0x56000040
#define S3C2440_SPI    0x59000000

/*****************************************************/
//S3C2440_CLKCON 部分
#define CLKCON      (*(volatile unsigned long *)(base_addr0 + 0x00))

//GPG 控制寄存器部分  GPG2脚对应NSS 端口
#define GPGCON      (*(volatile unsigned long *)(base_addr1 + 0x00))
#define GPGDAT      (*(volatile unsigned long *)(base_addr1 + 0x04))
#define GPGUP       (*(volatile unsigned long *)(base_addr1 + 0x08))

//GPE 控制寄存器部分
//GPE 11、12、13 脚分别对应SPI的MISO、MOSI、CLK 端口
#define GPECON      (*(volatile unsigned long *)(base_addr2 + 0x00))
#define GPEDAT      (*(volatile unsigned long *)(base_addr2 + 0x04))
#define GPEUP       (*(volatile unsigned long *)(base_addr2 + 0x08))

//SPI 控制寄存器部分
#define SPCON0      (*(volatile unsigned long *)(base_addr3 + 0x00))
#define SPSTA0      (*(volatile unsigned long *)(base_addr3 + 0x04))
#define SPPIN0      (*(volatile char *)(base_addr3 + 0x08))
#define SPPRE0      (*(volatile char *)(base_addr3 + 0x0C))
#define SPTDAT0     (*(volatile char *)(base_addr3 + 0x10))
#define SPRDAT0     (*(volatile char *)(base_addr3 + 0x14))

//SPI 输入输出的判忙状态引脚
#define SPI_TXRX_READY      (((SPSTA0) & 0x1) == 0x1)

#define  SPNSS0_DISABLE()      (GPEDAT &= ~(0x1 << 2))
#define  SPNSS0_ENABLE()       (GPEDAT |=  (0x1 << 2))
/********************************************************/
static int spi_open(struct inode *inode,struct file *filp)
{
    //使能时钟控制寄存器CLKCON 18位使能SPI
    CLKCON |= (0x01 << 18);//0x40000;
    printk("s3c2440_clkcon=%08ld\n",CLKCON);

    //使能GPG2 对应的NSS 端口
    //GPGCON |= (3 << 4);
    GPGCON &= ~(3 << 4);
    GPGCON |=  (1 << 4);
    SPNSS0_ENABLE();

    //使能GPE 11、12、13对应的 MISO0,MOSI0,SCK0 = 11 0x0000FC00*/
    GPECON &= ~((3 << 22) | (3 << 24) | (3 << 26));
    GPECON |=  ((2 << 22) | (2 << 24) | (2 << 26));

    //GPEUP 设置;全部disable
    GPGUP &= ~(0x07 << 2);
    GPEUP |=  (0x07 << 11);

    /*SPI 寄存器部分*/
    //SPI 预分频寄存器设置,
    //Baud Rate=PCLK/2/(Prescaler value+1)
    SPPRE0 = 0x18;       //freq = 1M
    printk("SPPRE0=%02X\n",SPPRE0);

    //polling,en-sck,master,low,format A,nomal = 0 | TAGD = 1
    SPCON0 = (0<<5)|(1<<4)|(1<<3)|(0<<2)|(0<<1)|(0<<0);
    printk("SPCON1=%02ld\n",SPCON0);

    //多主机错误检测使能
    SPPIN0 = (0 << 2) | (1 << 1) | (0 << 0);
    printk("SPPIN1=%02X\n",SPPIN0);

    //初始化程序
    SPTDAT0 = 0xff;
    return 0;
}


static int spi_release(struct inode *inode,struct file *filp)
{
    //释放掉在写函数操作里面申请的缓存空间
    kfree(kbuf);
    //printk("<1>release\n");
    return 0;
}

//向SPI寄存器SPI_SPTDAT1中写数据
static void writeByte(const char data)
{
    int j = 0;
    SPTDAT0 = data;
    while(!SPI_TXRX_READY)
        for(j = 0; j < 0xFF; j++);
}
//从SPI寄存器SPI_SPRDAT1中读取数据
static char readByte(const char data)
{
    int j = 0;
    char ch = 0;

    //发送任意数据，如果只是读取的话那
    //麽仍需向SPTDAT0写数据，来保证SPI的
    //时钟一直可用
    SPTDAT0 = data;

    //判忙标志位
    while(!SPI_TXRX_READY)
        for(j = 0; j < 0xFF; j++);

    //从寄存器中读取信息
    ch = SPRDAT0;
    return ch;
}

//接收数据并把数据发送到应用空间
static ssize_t spi_read(struct file *filp,char __user *buf,size_t count,loff_t *f_ops)
{
#if 1
    int   i = 0;
    char *tab;
    printk("<1>spi read!\n");
    tab = kmalloc(kbuf_size,GFP_KERNEL);

    for(; i < kbuf_size; i++){
        tab[i] = readByte(kbuf[i]);
        printk("read data tab[%d] = %02X\n",i, tab[i]);
    }
    copy_to_user(buf, tab, kbuf_size);
    kfree(tab);
#endif
    return 1;
}
//发送数据并把数据从用户空间发送到内核
static ssize_t spi_write(struct file *filp,const char __user *buf,
                                            size_t count,loff_t *f_ops)
{
    int i;
    //char *kbuf;
    kbuf_size = count;
    printk("<1>spi write!,count=%d\n",count);
    kbuf = kmalloc(count,GFP_KERNEL);

    //送到发用户空间
    if(copy_from_user(kbuf,buf,count))
    {
        printk("no enough memory!\n");
        return -1;
    }

    //循环写入寄存器
#if 0
    for(i=0;i
    {
        writeByte(kbuf[i]);
        printk("write 0x%02X!\n",*kbuf);
    }

#endif
    return count;
}


/**********************************************************/
static const struct file_operations spi_fops =
{
    .owner=THIS_MODULE,
    .open=spi_open,
    .read=spi_read,
    .release=spi_release,
    .write=spi_write,
};
static struct miscdevice misc = {
    .minor = MISC_DYNAMIC_MINOR,
    .name  = DEVICE_NAME,
    .fops  = &spi_fops,
};

static int __init spi_init(void)
{
    int ret;

    //映射时钟控制寄存器CLKCON
    base_addr0 = ioremap(S3C2440_CLKCON, 0x04);
    //映射GPG部分
    base_addr1 = ioremap(S3C2440_GPG, 0x10);
    //映射GPE 寄存器地址
    base_addr2 = ioremap(S3C2440_GPE, 0x10);
    //映射SPI 寄存器地址
    base_addr3 = ioremap(S3C2440_SPI, 0x20);

    //复杂设备的注册
    ret = misc_register(&misc);
    printk(DEVICE_NAME "\tinitialized\n");

    return ret;
}


static void __exit spi_exit(void)
{
    iounmap(base_addr0);
    iounmap(base_addr1);
    iounmap(base_addr2);
    iounmap(base_addr3);
    misc_deregister(&misc);
    printk("<1>spi_exit!\n");
}

module_init(spi_init);
module_exit(spi_exit);

MODULE_LICENSE("GPL");

/******************************************** *说明：本实验是针对TQ2440的SPI测试程序 * *设备模型：混杂设备 * *内核选取：linux-2.6.32.2 * *硬件要求：将MOSI与MISO短结 * *写作时间：2011/12/10 * *编辑作者：Sheldon Chu * ********************************************/ #include #include #include #include #include #include #include #include int loopChar=0x11; module_param(loopChar,int,S_IRUGO); #define DEVICE_NAME "tq2440_spi" static void __iomem *base_addr0; static void __iomem *base_addr1; static void __iomem *base_addr2; static void __iomem *base_addr3; //定义一个测试用的要发送的数据缓存包 static char *kbuf; static int kbuf_size; #define S3C2440_CLKCON 0x4c00000c #define S3C2440_GPG 0x56000060 #define S3C2440_GPE 0x56000040 #define S3C2440_SPI 0x59000000 /*****************************************************/ //S3C2440_CLKCON 部分 #define CLKCON (*(volatile unsigned long *)(base_addr0 + 0x00)) //GPG 控制寄存器部分 GPG2脚对应NSS 端口 #define GPGCON (*(volatile unsigned long *)(base_addr1 + 0x00)) #define GPGDAT (*(volatile unsigned long *)(base_addr1 + 0x04)) #define GPGUP (*(volatile unsigned long *)(base_addr1 + 0x08)) //GPE 控制寄存器部分 //GPE 11、12、13 脚分别对应SPI的MISO、MOSI、CLK 端口 #define GPECON (*(volatile unsigned long *)(base_addr2 + 0x00)) #define GPEDAT (*(volatile unsigned long *)(base_addr2 + 0x04)) #define GPEUP (*(volatile unsigned long *)(base_addr2 + 0x08)) //SPI 控制寄存器部分 #define SPCON0 (*(volatile unsigned long *)(base_addr3 + 0x00)) #define SPSTA0 (*(volatile unsigned long *)(base_addr3 + 0x04)) #define SPPIN0 (*(volatile char *)(base_addr3 + 0x08)) #define SPPRE0 (*(volatile char *)(base_addr3 + 0x0C)) #define SPTDAT0 (*(volatile char *)(base_addr3 + 0x10)) #define SPRDAT0 (*(volatile char *)(base_addr3 + 0x14)) //SPI 输入输出的判忙状态引脚 #define SPI_TXRX_READY (((SPSTA0) & 0x1) == 0x1) #define SPNSS0_DISABLE() (GPEDAT &= ~(0x1 << 2)) #define SPNSS0_ENABLE() (GPEDAT |= (0x1 << 2)) /********************************************************/ static int spi_open(struct inode *inode,struct file *filp) { //使能时钟控制寄存器CLKCON 18位使能SPI CLKCON |= (0x01 << 18);//0x40000; printk("s3c2440_clkcon=%08ld\n",CLKCON); //使能GPG2 对应的NSS 端口 //GPGCON |= (3 << 4); GPGCON &= ~(3 << 4); GPGCON |= (1 << 4); SPNSS0_ENABLE(); //使能GPE 11、12、13对应的 MISO0,MOSI0,SCK0 = 11 0x0000FC00*/ GPECON &= ~((3 << 22) | (3 << 24) | (3 << 26)); GPECON |= ((2 << 22) | (2 << 24) | (2 << 26)); //GPEUP 设置;全部disable GPGUP &= ~(0x07 << 2); GPEUP |= (0x07 << 11); /*SPI 寄存器部分*/ //SPI 预分频寄存器设置, //Baud Rate=PCLK/2/(Prescaler value+1) SPPRE0 = 0x18; //freq = 1M printk("SPPRE0=%02X\n",SPPRE0); //polling,en-sck,master,low,format A,nomal = 0 | TAGD = 1 SPCON0 = (0<<5)|(1<<4)|(1<<3)|(0<<2)|(0<<1)|(0<<0); printk("SPCON1=%02ld\n",SPCON0); //多主机错误检测使能 SPPIN0 = (0 << 2) | (1 << 1) | (0 << 0); printk("SPPIN1=%02X\n",SPPIN0); //初始化程序 SPTDAT0 = 0xff; return 0; } static int spi_release(struct inode *inode,struct file *filp) { //释放掉在写函数操作里面申请的缓存空间 kfree(kbuf); //printk("<1>release\n"); return 0; } //向SPI寄存器SPI_SPTDAT1中写数据 static void writeByte(const char data) { int j = 0; SPTDAT0 = data; while(!SPI_TXRX_READY) for(j = 0; j < 0xFF; j++); } //从SPI寄存器SPI_SPRDAT1中读取数据 static char readByte(const char data) { int j = 0; char ch = 0; //发送任意数据，如果只是读取的话那 //麽仍需向SPTDAT0写数据，来保证SPI的 //时钟一直可用 SPTDAT0 = data; //判忙标志位 while(!SPI_TXRX_READY) for(j = 0; j < 0xFF; j++); //从寄存器中读取信息 ch = SPRDAT0; return ch; } //接收数据并把数据发送到应用空间 static ssize_t spi_read(struct file *filp,char __user *buf,size_t count,loff_t *f_ops) { #if 1 int i = 0; char *tab; printk("<1>spi read!\n"); tab = kmalloc(kbuf_size,GFP_KERNEL); for(; i < kbuf_size; i++){ tab[i] = readByte(kbuf[i]); printk("read data tab[%d] = %02X\n",i, tab[i]); } copy_to_user(buf, tab, kbuf_size); kfree(tab); #endif return 1; } //发送数据并把数据从用户空间发送到内核 static ssize_t spi_write(struct file *filp,const char __user *buf, size_t count,loff_t *f_ops) { int i; //char *kbuf; kbuf_size = count; printk("<1>spi write!,count=%d\n",count); kbuf = kmalloc(count,GFP_KERNEL); //送到发用户空间 if(copy_from_user(kbuf,buf,count)) { printk("no enough memory!\n"); return -1; } //循环写入寄存器 #if 0 for(i=0;ispi_exit!\n"); } module_init(spi_init); module_exit(spi_exit); MODULE_LICENSE("GPL"); /***********************************************************
                                这是应用程序部分：

                                      spi_app.c

***********************************************************/

#include
#include
#include
#include
#include
#include
#include
#define  DATA_SIZE 5

int main(int argc, char **argv)
{
    int fd;
    int count=0;
    int i = 0;
    char buf[DATA_SIZE]={0x11,0x22,0x33,0x44,0x55};
    char tab[DATA_SIZE]={0};
    fd = open("/dev/tq2440_spi", O_RDWR);
    if (fd < 0) {
        perror("open device spi");
        exit(1);
    }
#if 1
    count=write(fd,buf,sizeof(buf)/sizeof(buf[0]));
    printf("1--->count= %d\n",count);
    count=read(fd,tab,sizeof(tab)/sizeof(tab[0]));
    printf("2--->count= %d\n",count);
/*
    for(; i < DATA_SIZE; i++) {
        count=write(fd,&buf[i],sizeof(buf[i]));
        count=read(fd,&tab[i],sizeof(tab[i]));
    }
*/
    for(i = 0; i < DATA_SIZE; i++){
        printf("write %d byte is: 0x%02X\n", i, buf[i]);
        printf("read  %d byte is: 0x%02X\n\n", i, tab[i]);
    }
#endif

    printf("-->hello!\n");
    close(fd);
    return 0;
}

#include #include #include #include #include #include #include #define DATA_SIZE 5 int main(int argc, char **argv) { int fd; int count=0; int i = 0; char buf[DATA_SIZE]={0x11,0x22,0x33,0x44,0x55}; char tab[DATA_SIZE]={0}; fd = open("/dev/tq2440_spi", O_RDWR); if (fd < 0) { perror("open device spi"); exit(1); } #if 1 count=write(fd,buf,sizeof(buf)/sizeof(buf[0])); printf("1--->count= %d\n",count); count=read(fd,tab,sizeof(tab)/sizeof(tab[0])); printf("2--->count= %d\n",count); /* for(; i < DATA_SIZE; i++) { count=write(fd,&buf[i],sizeof(buf[i])); count=read(fd,&tab[i],sizeof(tab[i])); } */ for(i = 0; i < DATA_SIZE; i++){ printf("write %d byte is: 0x%02X\n", i, buf[i]); printf("read %d byte is: 0x%02X\n\n", i, tab[i]); } #endif printf("-->hello!\n"); close(fd); return 0; } /***********************************************************
                                这是编译程序部分：

                                         Makefile

***********************************************************/

ifneq ($(KERNELRELEASE),)
obj-m := spi_ker.o
else
KDIR := /home/kernel/linux-2.6.32.2
all:
    make -C $(KDIR) M=$(PWD) modules ARCH=arm CROSS_COMPILE=arm-linux-
    arm-linux-gcc spi_app.c -o spi_app
clean:
    rm -f *.ko *.o *.mod.o *.mod.c *symvers modul* spi_app
endif