6-华为防火墙:配置基于源IP地址的NAT


一、实验一:配置No-Pat
1、基本配置略:
2、R1开启Telnet功能:
[R1]user-interface vty 0 4
[R1-ui-vty0-4]authentication-mode password ?
Please press ENTER to execute command
[R1-ui-vty0-4]authentication-mode password
Please configure the login password (maximum length 16):cisco
[R1-ui-vty0-4]user privilege level 15
3、配置Trust到Untrust的Zone间策略:
[SRG]policy interzone trust untrust outbound
[SRG-policy-interzone-trust-untrust-outbound]policy create-mode auto-sort enable
[SRG-policy-interzone-trust-untrust-outbound]policy 5
[SRG-policy-interzone-trust-untrust-outbound-5]policy source 192.168.1.0 mask 24
[SRG-policy-interzone-trust-untrust-outbound-5]policy destination 202.100.1.0 mask 24
[SRG-policy-interzone-trust-untrust-outbound-5]policy service service-set telnet
[SRG-policy-interzone-trust-untrust-outbound-5]policy service service-set icmp
[SRG-policy-interzone-trust-untrust-outbound-5]action permit
4、NAT未部署前地址未转换:
telnet 202.100.1.1
Login authentication
Password:cisco

5、配置no-pat:
[SRG]nat address-group 1 202.100.1.10 202.100.1.20 //创建地址组
[SRG]nat-policy interzone trust untrust outbound //创建Zone间NAT策略
[SRG-nat-policy-interzone-trust-untrust-outbound]policy 0
[SRG-nat-policy-interzone-trust-untrust-outbound-0]policy source 192.168.1.0 mask 24 //需要转换的源地址段
[SRG-nat-policy-interzone-trust-untrust-outbound-0]address-group 1 no-pat //转换后的地址组,并且不转换到端口
[SRG-nat-policy-interzone-trust-untrust-outbound-0]action source-nat //执行源转换动作
测试:
telnet 202.100.1.1

查看防火墙会话转换:
[SRG]display firewall session table verbose //源端口50573,转换后端口依然是50573

查看防火墙Map:
[SRG]display firewall server-map

二:实验二:配置PAT,有外部地址池的端口转换
[SRG-nat-policy-interzone-trust-untrust-outbound-0]undo address-group
[SRG-nat-policy-interzone-trust-untrust-outbound-0]address-group 1
测试:
telnet 202.100.1.1
[SRG]display firewall session table verbose

三、实验三:配置Easy-IP,转换192.168.1.2到USG的g0/0/0接口地址
[SRG]nat-policy interzone trust untrust outbound
[SRG-nat-policy-interzone-trust-untrust-outbound-1]policy 0
[SRG-nat-policy-interzone-trust-untrust-outbound-0]undo address-group
[SRG-nat-policy-interzone-trust-untrust-outbound-0]easy-ip GigabitEthernet 0/0/0
测试:
[SRG]display firewall session table verbose

转载于:https://blog.51cto.com/13856092/2138637

你可能感兴趣的:(6-华为防火墙:配置基于源IP地址的NAT)