华为3com交换路由命令详解

交换机命令
[Quidway]super password                                       ;修改特权用户密码
[Quidway]sysname                                       ;交换机命名
[Quidway]interface ethernet 0/1                               ;进入接口视图
[Quidway]interface vlan x                                ;进入接口视图
[Quidway-Vlan-interfacex]ip address 10.65.1.1 255.255.0.0     ;配置 VLAN IP 地址
[Quidway]ip route-static 0.0.0 .0 0.0.0.0 10.65.1.2            ;静态路由=网关
 
 
[Quidway]user-interface vty 0 4                               ;进入虚拟终端
[S3026-ui-vty0-4]authentication-mode password                 ;设置口令模式
[S3026-ui-vty0-4]set authentication-mode password simple 222  ;设置口令
[S3026-ui-vty0-4]user privilege level 3                       ;用户级别
 
 
[Quidway-Ethernet0/1]duplex {half|full|auto}                  ;配置端口工作状态
[Quidway-Ethernet0/1]speed {10|100|auto}                  ;配置端口工作速率
[Quidway-Ethernet0/1]flow-control                        ;配置端口流控
[Quidway-Ethernet0/1]mdi {across|auto|normal}                 ;配置端口平接扭接
[Quidway-Ethernet0/1]port link-type {trunk|access|hybrid}     ;设置端口工作模式
[Quidway-Ethernet0/1]undo shutdown                       ;激活端口
[Quidway-Ethernet0/2]quit                               ;退出系统视图
 
 
[Quidway]vlan 3                                         ;创建 VLAN
[Quidway-vlan3]port ethernet 0/1 to ethernet 0/4         ;在 VLAN 中增加端口
[Quidway-Ethernet0/2]port access vlan 3                  ;当前端口加入到 VLAN
[Quidway-Ethernet0/2]port trunk permit vlan {ID|All}        ;设 trunk 允许的 VLAN
[Quidway-Ethernet0/2]port trunk pvid vlan 3          ;设置 trunk 端口的 PVID
 
 
[Quidway]monitor-port <interface_type interface_num>         ;指定镜像端口
[Quidway]port mirror <interface_type interface_num>         ;指定被镜像端口
[Quidway]port mirror int_list observing-port int_type int_num ;指定镜像和被镜像
 
 
[Quidway]description string                              ;指定 VLAN 描述字符
[Quidway]description                                   ;删除 VLAN 描述字符
[Quidway]display vlan [vlan_id]                               ;查看 VLAN 设置
 
 
[Quidway]stp {enable|disable}                                 ;设置生成树 , 默认关闭
[Quidway]stp priority 4096                               ;设置交换机的优先级
[Quidway]stp root {primary|secondary}                    ;设置为根或根的备份
[Quidway-Ethernet0/1]stp cost 200                        ;设置交换机端口的花费
 
 
[SwitchA-vlanx]isolate-user-vlan enable                  ;设置主 vlan
[SwitchA]Isolate-user-vlan <x> secondary <list>          ;设置主 vlan 包括的子 vlan
[Quidway-Ethernet0/2]port hybrid pvid vlan <id>          ;设置 vlan pvid
[Quidway-Ethernet0/2]port hybrid pvid                    ;删除 vlan pvid
[Quidway-Ethernet0/2]port hybrid vlan vlan_id_list untagged  ;设置无标识的 vlan
如果包的 vlan id PVId 一致,则去掉 vlan 信息 . 默认 PVID=1
所以设置 PVID 为所属 vlan id, 设置可以互通的 vlan untagged.
----------------------------------------
路由器命令
 
[Quidway]display version                                ;显示版本信息
[Quidway]display current-configuration                   ;显示当前配置
[Quidway]display interfaces                             ;显示接口信息
[Quidway]display ip route                               ;显示路由信息
 
 
[Quidway]sysname aabbcc                                 ;更改主机名
[Quidway]super passwrod 123456                           ;设置口令
[Quidway]interface serial0                              ;进入接口
[Quidway-serial0]ip address <ip> <mask|mask_len>        ;配置端口 IP 地址
[Quidway-serial0]undo shutdown                          ;激活端口
[Quidway]link-protocol hdlc                              ;绑定 hdlc 协议
[Quidway]user-interface vty 0 4
[Quidway-ui-vty0-4]authentication-mode password
[Quidway-ui-vty0-4]set authentication-mode password simple 222
[Quidway-ui-vty0-4]user privilege level 3
[Quidway-ui-vty0-4]quit
 
 
[Quidway]debugging hdlc all serial0                     ;显示所有信息
[Quidway]debugging hdlc event serial0                   ;调试事件信息
[Quidway]debugging hdlc packet serial0                  ;显示包的信息
 
 
静态路由:
[Quidway]ip route-static <ip><mask>{interface number|nexthop}[value][reject|blackhole]
例如:
[Quidway]ip route-static 129.1.0.0 16 10.0.0 .2
[Quidway]ip route-static 129.1.0.0 255.255.0.0 10.0.0 .2
[Quidway]ip route-static 129.1.0.0 16 Serial 2
[Quidway]ip route-static 0.0.0 .0 0.0.0.0  10.0.0 .2
 
 
动态路由:
[Quidway]rip                                                   ;设置动态路由
[Quidway]rip work                                             ;设置工作允许
[Quidway]rip input                                            ;设置入口允许
[Quidway]rip output                                           ;设置出口允许
[Quidway-rip]network 1.0.0 .0                             ;设置交换路由网络
[Quidway-rip]network all                                      ;设置与所有网络交换
[Quidway-rip]peer ip-address                                 
[Quidway-rip]summary                                           ;路由聚合
[Quidway]rip version 1                                        ;设置工作在版本 1
[Quidway]rip version 2 multicast                              ;设置工作在版本 2 ,多播方式
[Quidway-Ethernet0]rip split-horizon                          ;水平分隔
 
 
[Quidway]router id A.B.C.D                                     ;配置路由器的 ID
[Quidway]ospf enable                                          ;启动 OSPF 协议
[Quidway-ospf]import-route direct                             ;引入直联路由
[Quidway-Serial0]ospf enable area <area_id>                   ;配置 OSPF 区域
 
 
标准访问列表命令格式如下:
acl <acl-number> [match-order config|auto]                    ;默认前者顺序匹配。
rule [normal|special]{permit|deny} [source source-addr source-wildcard|any]
例:
[Quidway]acl 10
[Quidway-acl-10]rule normal permit source 10.0.0 .0 0.0.0.255
[Quidway-acl-10]rule normal deny source any
 
 
扩展访问控制列表配置命令
配置 TCP/UDP 协议的扩展访问列表:
rule {normal|special}{permit|deny}{tcp|udp}source {<ip wild>|any}destination <ip wild>|any}
[operate]
 
 
配置 ICMP 协议的扩展访问列表:
rule {normal|special}{permit|deny}icmp source {<ip wild>|any]destination {<ip wild>|any]
[icmp-code] [logging]
 
 
扩展访问控制列表操作符的含义
equal portnumber                                        ;等于
greater-than portnumber                                        ;大于
less-than portnumber                                        ;小于
not-equal portnumber                                        ;不等
range portnumber1 portnumber2                                  ;区间
 
 
扩展访问控制列表举例
[Quidway]acl 101
[Quidway-acl-101]rule deny souce any destination any
[Quidway-acl-101]rule permit icmp source any destination any icmp-type echo
[Quidway-acl-101]rule permit icmp source any destination any icmp-type echo-reply
 
 
[Quidway]acl 102
[Quidway-acl-102]rule permit ip source 10.0.0 .1 0.0.0.0 destination 202.0.0.1 0.0.0.0
[Quidway-acl-102]rule deny ip source any destination any
 
 
[Quidway]acl 103
[Quidway-acl-103]rule permit tcp source any destination 10.0.0 .1 0.0.0.0 destination-port equal ftp
[Quidway-acl-103]rule permit tcp source any destination 10.0.0 .2 0.0.0.0 destination-port equal www
 
 
 
[Quidway]firewall enable
[Quidway]firewall default permit|deny
[Quidway]int e0
[Quidway-Ethernet0]firewall packet-filter 101 inbound|outbound
 
 
 
地址转换配置举例
[Quidway]firewall enable
[Quidway]firewall default permit
[Quidway]acl 101
[Quidway-acl-101]rule deny ip source any destination any
[Quidway-acl-101]rule permit ip source 129.38.1.4 0 destination any
[Quidway-acl-101]rule permit ip source 129.38.1.1 0 destination any
[Quidway-acl-101]rule permit ip source 129.38.1.2 0 destination any
[Quidway-acl-101]rule permit ip source 129.38.1.3 0 destination any
[Quidway]acl 102
[Quidway-acl-102]rule permit tcp source 202.39.2.3 0 destination 202.38.160.1 0
[Quidway-acl-102]rule permit tcp source any destination 202.38.160.1 0 destination-port great-than
1024
 
 
[Quidway-Ethernet0]firewall packet-filter 101 inbound
[Quidway-Serial0]firewall packet-filter 102 inbound
 
 
[Quidway]nat address-group 202.38.160.101 202.38.160.103 pool1
[Quidway]acl 1
[Quidway-acl-1]rule permit source 10.110.10.0 0.0.0 .255
[Quidway-acl-1]rule deny source any
[Quidway-acl-1]int serial 0
[Quidway-Serial0]nat outbound 1 address-group pool1
 
 
[Quidway-Serial0]nat server global 202.38.160.101 inside 10.110.10.1 ftp tcp
[Quidway-Serial0]nat server global 202.38.160.102 inside 10.110.10.2 www tcp
[Quidway-Serial0]nat server global 202.38.160.102 8080 inside 10.110.10.3 www tcp
[Quidway-Serial0]nat server global 202.38.160.103 inside 10.110.10.4 smtp udp
 
 
 
PPP 验证:
主验方: pap|chap
[Quidway]local-user u2 password {simple|cipher} aaa
[Quidway]interface serial 0
[Quidway-serial0]ppp authentication-mode {pap|chap}
[Quidway-serial0]ppp chap user u1        //pap 时,不用此句
 
 
pap 被验方:
[Quidway]interface serial 0
[Quidway-serial0]ppp pap local-user u2 password {simple|cipher} aaa
 
 
chap 被验方:
[Quidway]interface serial 0
[Quidway-serial0]ppp chap user u1
[Quidway-serial0]local-user u2 password {simple|cipher} aaa

你可能感兴趣的:(职场,华为,休闲,3com,交换路由)