eth2>eth0

一台Vmware虚拟机更换宿主Server启动以后提示找不到eth0，网卡无法加载。出现这个问题的原因我想是因为更换了宿主Server，原来虚拟出来的网卡Mac地址也跟着改变，也就相当于更换了Vmware虚拟机的网卡。

用 ifconfig -a 命令查看所有的网络设置，果然没有eth0的相关设置，多出来一个eth2。显示如下：
 

QUOTE:

eth2 Link encap:Ethernet HWaddr 00:0C:29:AF:1C:C7 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:185 Base address:0x1480 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:3054386 errors:0 dropped:0 overruns:0 frame:0 TX packets:3054386 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1067784027 (1018.3 MiB) TX bytes:1067784027 (1018.3 MiB)

由于系统默认的启动网卡是eth0，所以怎么样把eth2更改为eth0成了当务之急。查了很多资料最终终于找到解决方法，方法如下：

修改文件/etc/udev/rules.d/z25_persistent-net.rules 文件，原来为：
 

QUOTE:

protime-linux:/etc/udev/rules.d# cat z25_persistent-net.rules # This file was automatically generated by the /lib/udev/write_net_rules # program, probably run by the persistent-net-generator.rules rules file. # # You can modify it, as long as you keep each rule on a single line. # MAC addresses must be written in lowercase. # PCI device 0x1022:0x2000 (pcnet32) SUBSYSTEM=="net", DRIVERS=="?*", ATTRS{address}=="00:0c:29:15:3a:48", NAME="eth0" # PCI device 0x1022:0x2000 (pcnet32) SUBSYSTEM=="net", DRIVERS=="?*", ATTRS{address}=="00:0c:29:15:3a:52", NAME="eth1" # PCI device 0x1022:0x2000 (pcnet32) SUBSYSTEM=="net", DRIVERS=="?*", ATTRS{address}=="00:0c:29:af:1c:c7", NAME="eth2"

修改后：
 

QUOTE:

protime-linux:/etc/udev/rules.d# cat z25_persistent-net.rules # This file was automatically generated by the /lib/udev/write_net_rules # program, probably run by the persistent-net-generator.rules rules file. # # You can modify it, as long as you keep each rule on a single line. # MAC addresses must be written in lowercase. # PCI device 0x1022:0x2000 (pcnet32) SUBSYSTEM=="net", DRIVERS=="?*", ATTRS{address}=="00:0c:29:15:3a:48", NAME="eth2" # PCI device 0x1022:0x2000 (pcnet32) SUBSYSTEM=="net", DRIVERS=="?*", ATTRS{address}=="00:0c:29:15:3a:52", NAME="eth1" # PCI device 0x1022:0x2000 (pcnet32) SUBSYSTEM=="net", DRIVERS=="?*", ATTRS{address}=="00:0c:29:af:1c:c7", NAME="eth0"

保存重启后可以看到原来的网络配置又回来了。

还有一个方法就是把eth2设置为默认启动的网卡，修改/etc/network/interfaces：

修改前：
 

QUOTE:

protime-linux:/etc/udev/rules.d# cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface #allow-hotplug eth0 auto eth0 iface eth0 inet static address 192.168.0.224 netmask 255.255.255.0 gateway 192.168.0.9 #iface eth0 inet dhcp auto eth0:0 iface eth0:0 inet static name Ethernet Lan card address 192.168.0.223 netmask 255.255.255.0 gateway 192.168.0.9

修改后为：
 

QUOTE:

# This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface #allow-hotplug eth0 auto eth2 iface eth2 inet static address 192.168.0.224 netmask 255.255.255.0 gateway 192.168.0.9 #iface eth0 inet dhcp auto eth2:0 iface eth0:0 inet static name Ethernet Lan card address 192.168.0.223 netmask 255.255.255.0 gateway 192.168.0.9

保存后重启server应该也可以启动网卡。（