设备验货流程及命令

今天XX行的新核心设备7607到货，下午去验货

这里简单说一下验货的流程和要用到的命令

1.拆开封条，将机身的序列号抄下来

2.拆箱检查设备，配件

3.将配备的业务板卡，模块等插入设备,注意静电，相当危险

4.将电脑接入console口，打开CRT，打开文档记录，将文档存到适当的位置。

5.加电，自检。从现在开始，76的上的所有东西将被记录到文档里面，方便设备有问题开case用

6，76的自检是相当的快，不愧是新平台，样子和H3C的路由器有点相似，可惜没带相机。

7.运行相关命令，命令查看完毕后，关闭文档记录，接下来你就可以尽情的玩啦，别保存哦

下面是主要的命令，有重要的地方我会贴出来

Router#sh version     查看版本
Router#sh run    产看配置  ，要是有配置就说明有点问题，注意

mls ip slb purge global
mls ip multicast flow-stat-timer 9
mls flow ip interface-full
no mls acl tcam share-global
mls cef error action reset
multilink bundle-name authenticated
spanning-tree mode pvst      运行了生成树，7665的板卡是路由交换平台，可以插路由板卡，可以插65 的交换板卡
spanning-tree extend system-id
diagnostic cns publish cisco.cns.device.diag_results
diagnostic cns subscribe cisco.cns.device.diag_commands
fabric timer 15
!

vlan internal allocation policy ascending
vlan access-log ratelimit 2000

controller E1 1/0/0     第一插槽的0端口插入了一块8E1板卡
!        
controller E1 1/0/1
!        
controller E1 1/0/2
!        
controller E1 1/0/3
!        
controller E1 1/0/4
!        
controller E1 1/0/5
!        
controller E1 1/0/6
!        
controller E1 1/0/7
!        
vlan internal allocation policy ascending
vlan access-log ratelimit 2000
!        
!        
!        
!        
!        
!        
interface GigabitEthernet5/1     光纤模块
 no ip address
 shutdown
!        
interface GigabitEthernet5/2    光纤模块

 no ip address
 shutdown
!        
interface GigabitEthernet6/1    光纤模块

 no ip address
 shutdown
!        
interface GigabitEthernet6/2    光纤模块

 no ip address
 shutdown
!        
interface Vlan1               VLAN
 no ip address
 shutdown

 

Router# sh module         查看槽位
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
  1    0  2 port adapter Enhanced FlexWAN        WS-X6582-2PA       JAE131885SE
  5    2  Route Switch Processor 720 (Active)    RSP720-3C-GE       JAE13177TJE
  6    2  Route Switch Processor 720 (Hot)       RSP720-3C-GE       JAE13177XSZ

Mod MAC addresses                       Hw    Fw           Sw           Status
--- ---------------------------------- ------ ------------ ------------ -------
  1  0025.45d0.fac0 to 0025.45d0.faff   2.4   12.2(33)SRD  12.2(33)SRD  Ok
  5  001c.584c.ed10 to 001c.584c.ed13   5.9   12.2(33r)SRD 12.2(33)SRD  Ok
  6  001c.584c.ef88 to 001c.584c.ef8b   5.9   12.2(33r)SRD 12.2(33)SRD  Ok

Mod  Sub-Module                  Model              Serial       Hw     Status
---- --------------------------- ------------------ ----------- ------- -------
  5  Policy Feature Card 3       7600-PFC3C         JAE13177Y7B  1.2    Ok
  5  C7600 MSFC4 Daughterboard   7600-MSFC4         JAE13177TW1  1.4    Ok
  6  Policy Feature Card 3       7600-PFC3C         JAE131781XF  1.2    Ok
  6  C7600 MSFC4 Daughterboard   7600-MSFC4         JAE131781XD  1.4    Ok

Mod  Online Diag Status
---- -------------------
  1  Pass
  5  Pass
  6  Pass

1槽位是两端口的业务承载板，可以插ATM，EI等

5，6槽位是引擎卡

 

 

Router#sh inventory        查看所有硬件的序列号（我贴了一部分）
NAME: "CISCO7606-S", DESCR: "Cisco Systems Cisco 7600 6-slot Chassis System"
PID: CISCO7606-S       , VID: V01, SN: FOX1305G3NT

NAME: "CLK-7600 1", DESCR: "OSR-7600 Clock FRU 1"
PID: CLK-7600          , VID:    , SN: NWG1248011U

NAME: "CLK-7600 2", DESCR: "OSR-7600 Clock FRU 2"
PID: CLK-7600          , VID:    , SN: NWG1248011U

NAME: "module 1", DESCR: "2 port adapter Enhanced FlexWAN Rev. 2.4"
PID: WS-X6582-2PA      , VID: V08, SN: JAE131885SE

NAME: "module 5", DESCR: "RSP720-3C-GE 2 ports Route Switch Processor 720 Rev. 5.9"
PID: RSP720-3C-GE      , VID: V07, SN: JAE13177TJE

NAME: "msfc sub-module of 5", DESCR: "7600-MSFC4 C7600 MSFC4 Daughterboard Rev. 1.4"
PID: 7600-MSFC4        , VID: 000, SN: JAE13177TW1

NAME: "switching engine sub-module of 5", DESCR: "7600-PFC3C Policy Feature Card 3 Rev. 1.2"
PID: 7600-PFC3C        , VID: 000, SN: JAE13177Y7B

 

 

Router# sh environment   查看硬件环境(贴了部分)
environmental alarms:  系统警报，电源没有冗余
system minor alarm on power-supply 1 power-output-fail (raised 00:05:44 ago)

backplane:
  operating clock count: 2
 
fan-tray 1:      风扇
  fan-tray 1 type: FAN-MOD-6SHS
  fan-tray 1 mode: Auto
  fan-tray 1 fan-fail: OK
clock 1:
  clock 1 OK: OK, clock 1 clock-inuse: in-use
clock 2:
  clock 2 OK: OK, clock 2 clock-inuse: not-in-use
power-supply 1:    电源一
  power-supply 1 power-output-fail: failed   没加电
power-supply 2:     电源二
  power-supply 2 fan-fail: OK
  power-supply 2 power-input: AC 220V  输入电压
  power-supply 2 power-output-mode: high    输出模式
  power-supply 2 incompatible with fan: OK
  power-supply 2 power-output-fail: OK
module 1:     槽位1（没有贴全）
  module 1 power-output-fail: OK
  module 1 outlet temperature: 44C
  module 1 inlet temperature: 29C

module 1 device-1 temperature: 27C
  module 1 device-2 temperature: 27C

 

chassis connector rating: 1680.00 Watts (40.00 Amps @ 42V)    
module 1
  module 1 connector rating: 1512.00 Watts (36.00 Amps @ 42V)
  module 1 power consumption: 105.00 Watts ( 2.50 Amps @ 42V)
module 5
  module 5 connector rating: 1260.00 Watts (30.00 Amps @ 42V)
  module 5 power consumption: 310.38 Watts ( 7.39 Amps @ 42V)
module 6
  module 6 connector rating: 1260.00 Watts (30.00 Amps @ 42V)
  module 6 power consumption: 310.38 Watts ( 7.39 Amps @ 42V)

chassis per slot cooling capacity: 91 cfm
ambient temperature: < 55C    温度
  module 1 cooling requirement: 30 cfm
  module 5 cooling requirement: 35 cfm
  module 6 cooling requirement: 35 cfm