Aggr是由一个或多个raid group (raid group包含一个校验盘和多个数据盘)组成的虚拟存储池.
卷(volume)建立在Aggr上的空间管理单位，是快照等技术实现的基本单元。存放系统数据的称为根卷(root volume). 其他存放数据的卷称为普通卷. 一个filer有且只有一个根卷
Aggr=一个或多个raid group
Aggr ----> vloume ---> lun
There are only four types of disks in Data ONTAP, I will discuss RAID in the aggregate section.
| Data | holds data stored within the RAID group |
| Spare | Does not hold usable data but is available to be added to a RAID group in an aggregate, also known as a hot spare |
| Parity | Store data reconstruction information within the RAID group |
| dParity | Stores double-parity information within the RAID group, if RAID-DP is enabled |
------------------------------------------------------------------------------------
http://blog.chinaunix.net/uid-20426600-id-1947255.html
型号是netapp fas3140，8个盘柜，共112块磁盘，做过两次扩容，4个loop，因为不是一次性规划，有点乱
ssh方式未启用，用telnet登录的，命令类似于unix，据说Data ONTAP系统 是由unix内核裁剪定制而来的，
netapp-a> sysconfig
NetApp Release 7.2.6.1: Wed Dec 10 21:10:08 PST 2008
System ID: 015172xxxx (hfnetapp-a); partner ID: 015172xxxx (hfnetapp-b)
System Serial Number: 8000xxxx (hfnetapp-a)
System Rev: A0
slot 0: System Board
Processors: 2
Memory Size: 4096 MB
Memory Attributes: Bank Interleaving
Hoisting
Chipkill ECC
Controller: A
Remote LAN Module Status: Online
slot 0: Internal BGE 10/100 Ethernet Controller
e0M MAC Address: 00:a0:98:12:3e:86 (auto-unknown-cfg_down)
slot 0: BGE 10/100/1000 Ethernet Controller
e0a MAC Address: 00:a0:98:12:3e:84 (auto-1000t-fd-up)
e0b MAC Address: 00:a0:98:12:3e:85 (auto-unknown-down)
slot 0: NVRAM
Memory Size: 512 MB
slot 0: FC Host Adapter 0a
42 Disks: 5712.0GB
3 shelves with ESH4
slot 0: Fibre Channel Target Host Adapter 0b
slot 0: FC Host Adapter 0c
28 Disks: 3808.0GB
2 shelves with ESH4
slot 0: Fibre Channel Target Host Adapter 0d
slot 0: NetApp ATA/IDE Adapter 0e (0x00000000000001f0)
0e.0 977MB
slot 1: FC Host Adapter 1a
14 Disks: 1904.0GB
1 shelf with ESH4
slot 1: FC Host Adapter 1b
28 Disks: 3808.0GB
2 shelves with ESH4
slot 1: FC Host Adapter 1c
slot 1: FC Host Adapter 1d
slot 2: FC Host Adapter 2a
slot 2: FC Host Adapter 2b
slot 2: FC Host Adapter 2c
slot 2: FC Host Adapter 2d
1.磁盘。
netapp-a> disk
usage: disk
Options are:
fail [-i] [-f] - fail a file system disk
remove [-w] - remove a spare disk
swap - prepare (quiet) bus for swap
unswap - undo disk swap and resume service
scrub { start | stop } - start or stop disk scrubbing
assign { | all | -n | auto} [-p ] [-o ] [-s ] [-c block|zoned] [-f] - assign a disk to a filer or all unowned disks by specifying "all" ornumber of unowned disks
show [-o | -s | -n | -v | -a] - lists disks and owners
replace {start [-f] [-m] } | {stop } - replace a file system disk with a spare disk or stop replacing
zero spares - Zero all spare disks
checksum { | all} [-c block | zoned]
sanitize { start | abort | status | release } - sanitize one or more disks
maint { start | abort | status | list} - run maintenance tests on one or more disks
netapp-b> disk show
DISK OWNER POOL SERIAL NUMBER
------------ ------------- ----- -------------
1a.23 netapp-a(151727447) Pool0 3KN0RNVS00007618ZJV6
1a.20 netapp-a(151727447) Pool0 3KN0R2WM000076191PH8
1a.22 netapp-a(151727447) Pool0 3KN0R4B6000076191P8H
0a.59 netapp-a(151727447) Pool0 JNV0D86C
0a.56 netapp-a(151727447) Pool0 JNV04S0C
1b.45 netapp-b(151727512) Pool0 JNV01PWC
0c.44 netapp-b(151727512) Pool1 3LN6ZJEX0000991572L3
0c.25 netapp-b(151727512) Pool1 3LN1Y2L70000982170CQ
0c.32 netapp-b(151727512) Pool1 3LN6ZJFK00009915726L
0c.36 netapp-b(151727512) Pool1 3LN6ZJ0Y000099156J76
0c.26 netapp-b(151727512) Pool1 3LN6ZHYY0000991573J8
0a.16 netapp-a(151727447) Pool0 3LN7GQTV00009935HZU5
磁盘分配后，被分配到某一个filer，可以一次分配置一个，或用all选项分配所有未分配的 ,
pool的概念：
2.盘柜 shelf
一个loop可包含一个或多个盘柜。一个loop中的盘柜有 1 2 3 ...的序号，一个loop中的盘柜用两个串连链路连接,这两个链路分别连接到filer a ,filer b。loop在物理光纤链路上同时连接到两个filer
loop 不会属于某一个filer，只有loop中的盘柜里的磁盘会属于某一个filer。
3.aggr
一个filer中拥有若干块磁盘，
在一个filer上创建aggr
netapp-b> aggr create
aggr create: No aggregate name supplied.
usage:
aggr create
[-f] [-l ] [-L [compliance | enterprise]]
[-m] [-n] [-r ] [-R ]
[-T {ATA | EATA | FCAL | LUN | SAS | SATA | SCSI | XATA | XSAS}]
[-t {raid4 | raid_dp}] [-v]
- create a new aggregate using the disks in ;
is either
[@]
or
-d ...
[-d ... ].
If a mirrored aggregate is desired, make sure to specify
even number for , or to use two '-d' lists.
netapp-b>
netapp-b> aggr add
aggr add: No aggregate name supplied.
usage:
aggr add [-f] [-n] [-g ]
- add disks listed in to aggregate ;
is either:
[@]
or
-d ...
[-d ... ].
netapp-b>
创建aggr时指定使用哪些磁盘（disk-list）、raid类型、raid大小（即磁盘块数）
netapp-b> aggr status
Aggr State Status Options
aggr2 online raid4, aggr raidsize=14
aggr1 online raid4, aggr raidsize=14
aggr0 online raid_dp, aggr root, raidsize=28
4 vol
netapp-a> vol create
vol create: No volume name supplied.
usage:
vol create
{ [-l ] [-s {none | file | volume}]
[k|m|g|t]
[-S remotehost:remotevolume] }
|
{ [-f] [-l ] [-m] [-n]
[-L [compliance | enterprise]]
[-r ] [-t {raid4 | raid_dp}]
}
- create a new volume, either a flexible volume from an existing
aggregate, or a traditional volume from a disk list. A disk
list is either
[@]
or
-d ...
[-d ... ].
netapp-a> vol add
vol add: No volume name supplied.
usage:
vol add [-f] [-n] [-g ]
- add disks listed in to traditional volume ;
is either:
[@]
or
-d ...
[-d ... ].
netapp-a>
netapp-a> vol status
Volume State Status Options
vol4 online raid4, flex create_ucode=on
vol0 online raid_dp, flex root, create_ucode=on
vol1 online raid_dp, flex create_ucode=on
vol2 online raid_dp, flex create_ucode=on
vol3 online raid4, flex create_ucode=on
6.lun
创建lun要指定lun_path 即上面的 vol
netapp-a> lun
The following commands are available; for more information
type "lun help "
clone help online share
comment map resize show
config_check maxsize serial snap
create move set stats
destroy offline setup unmap
netapp-a> lun stats
/vol/vol4/lun7 (323 days, 5 hours, 34 minutes, 44 seconds)
Read (kbytes) Write (kbytes) Read Ops Write Ops
390084 101402642 25767 646497
/vol/vol2/lun3 (323 days, 6 hours, 25 minutes, 54 seconds)
Read (kbytes) Write (kbytes) Read Ops Write Ops
3894011821 10653462004 169908898 968023745
/vol/vol3/lun4 (323 days, 6 hours, 25 minutes, 54 seconds)
Read (kbytes) Write (kbytes) Read Ops Write Ops
1656369662 1836904108 35720470 112092751
/vol/vol1/lun2 (323 days, 6 hours, 25 minutes, 54 seconds)
Read (kbytes) Write (kbytes) Read Ops Write Ops
94157217558 2535260540 1069989465 49700110
netapp-a> lun show
/vol/vol1/lun2 1.2t (1363845054464) (r/w, online, mapped)
/vol/vol2/lun3 1.2t (1353030041600) (r/w, online, mapped)
/vol/vol3/lun4 1000.1g (1073858215936) (r/w, online, mapped)
/vol/vol4/lun7 1020g (1095216660480) (r/w, online, mapped)
netapp-a> lun create
lun create: exactly one of -s, -f and -b should be supplied
usage:
lun create -s -t [ -o noreserve ]
lun create -f -t [ -o noreserve ]
lun create -b [ -o noreserve ]
- create (writable) LUN storage at the LUN path specified.
NOTE: 'lun create -b' has been deprecated.
Please consider using 'lun clone create' instead.
For more information, try 'lun help create' or 'man na_lun'
netapp-a> lun map
usage:
lun map [ -f ] [ ]
- make a LUN accessible to initiators in the specified group, at
the LUN ID specified.
The LUN ID is a number in the range 0 through 4095. If none is
specified, the lowest available LUN ID will be used.
Once created the LUN mappings can be displayed using "lun show -m".
Note that a LUN can be exported to multiple initiator groups.
The LUN ID at which it is exported to these groups need not be
the same.
Note that an exported LUN is immediately available for target-
mode accesses. To prevent accesses, use "lun offline".
Initiator groups are created and managed using the "igroup"
command.
If -f is used, LUN mapping conflict checks will not be done on
the cluster partner
For more information, try 'man na_lun'
netapp-a>
7.igroup (initiator_group,即主机上面的initiator发起连接是对应到一个igroup，在存储上一个igroup要映射到一个或多个lun ,用lun map命令)
netapp-b> igrop
igrop not found. Type '?' for a list of commands
netapp-b> igroup
The following commands are available; for more information
type "igroup help "
add destroy rename show
bind help set unbind
create remove
netapp-b> igroup show
ihfdb (FCP) (ostype: linux):
21:00:00:1b:32:90:96:5d (logged in on: 0b)
21:00:00:1b:32:97:57:d9 (logged in on: 0d)
netapp-b> igroup create
igroup create: -f or -i must be specified
usage:
igroup create { -f | -i } -t [ -a ]
[ ... ]
- creates a new initiator group
An initiator group is a typed collection of initiators. The type
is specified with the -f (FCP) or the -i (iSCSI) options. Nodes
can optionally be supplied, they will be added to the group.
FCP nodes are specified as world wide port names (WWPN), written
as 16 hexadecimal characters with optional (:) characters. iSCSI
nodes are written in the dotted-domain fashion.
The ostype can be either solaris, windows, hpux, aix, linux,
netware or vmware. The type applies to all initiators within
the group, and governs the finer details of SCSI protocol interaction
with these initiators.
The -a option allows the newly created initiator group to be bound
to an already existing portset.
For more information, try 'man na_igroup'
netapp-b> igroup add
usage:
igroup add [ -f ] ...
- adds node(s) to an initiator group
If -f is used, LUN mapping conflict checks will not be done on
the cluster partner.
For more information, try 'man na_igroup'
netapp-b> igroup bind
usage:
igroup bind
- binds the igroup to the portset
The initiator group must not be currently bound to any portset
If the initiator group is bound, use the 'igroup unbind'
command to first unbind the initiator group before attempting
to bind to another portset.
For more information, try 'man na_igroup'
hfnetapp-b> igroup set
usage:
igroup set [ -f ]
- sets an attribute on an initiator group
The current attributes and values supported are:
ostype: solaris, windows, hpux, aix, linux, netware and
vmware. The ostype attribute sets the operating
system type of the initiators in the initiator group.
throttle_reserve: value of 0->99
The throttle_reserve attribute reserves the given
percentage of SCSI cmdblks for this initiator
throttle_borrow: yes, or no.
If yes, then an igroup can borrow cmdblks if it
exceeds its reserve and cmdblks are available.
alua: yes, or no.
If yes, then the initiators in the igroup can
support Assymetric Logical Unit Access.
The -f flag will override all warnings.
For more information, try 'man na_igroup'
netapp-b>
创建igroup时要指定 ostype(操作系统类型)、 portset（主机HBA卡 WWN号）
绑定igroup :binds the igroup to the portset
9.fcp
netapp-b> fcp show adapter
Slot: 0d
Description: Fibre Channel Target Adapter 0d (Dual-channel, QLogic 2432 (2462) rev. 2)
Adapter Type: Local
Status: ONLINE
FC Nodename: 50:0a:09:80:89:4b:2d:98 (500a0980894b2d98)
FC Portname: 50:0a:09:81:89:4b:2d:98 (500a0981894b2d98)
Standby: No
Slot: 0b
Description: Fibre Channel Target Adapter 0b (Dual-channel, QLogic 2432 (2462) rev. 2)
Adapter Type: Local
Status: ONLINE
FC Nodename: 50:0a:09:80:89:4b:2d:98 (500a0980894b2d98)
FC Portname: 50:0a:09:82:89:4b:2d:98 (500a0982894b2d98)
Standby: No
netapp-b> fcp show initiator
Initiators connected on adapter 0d:
Portname Group
21:00:00:1b:32:97:57:d9 ihfdb
Initiators connected on adapter 0b:
Portname Group
21:00:00:1b:32:90:96:5d ihfdb
netapp-b>
netapp-a> fcp show adapter
Slot: 0d
Description: Fibre Channel Target Adapter 0d (Dual-channel, QLogic 2432 (2462) rev. 2)
Adapter Type: Local
Status: ONLINE
FC Nodename: 50:0a:09:80:89:4b:2d:98 (500a0980894b2d98)
FC Portname: 50:0a:09:81:99:4b:2d:98 (500a0981994b2d98)
Standby: No
Slot: 0b
Description: Fibre Channel Target Adapter 0b (Dual-channel, QLogic 2432 (2462) rev. 2)
Adapter Type: Local
Status: ONLINE
FC Nodename: 50:0a:09:80:89:4b:2d:98 (500a0980894b2d98)
FC Portname: 50:0a:09:82:99:4b:2d:98 (500a0982994b2d98)
Standby: No
netapp-a> fcp show initiator
Initiators connected on adapter 0d:
Portname Group
21:00:00:1b:32:97:41:cb ihfdb-a
Initiators connected on adapter 0b:
Portname Group
21:00:00:1b:32:90:0f:5e ihfdb-a
hfnetapp-a>
*****************************on host*******10.10.1.11******************************
[root@db2 qla2xxx]# cat /proc/scsi/qla2xxx/3
QLogic PCI to Fibre Channel Host Adapter for QLE2460:
Firmware version 4.04.00 [IP] [84XX] , Driver version 8.02.09-d0-rhel4.7-04
ISP: ISP2432
Request Queue = 0x17d9600000, Response Queue = 0x17d95c0000
Request Queue count = 4096, Response Queue count = 512
Total number of active commands = 2
Total number of interrupts = 2852508411
Device queue depth = 0x20
Number of free request entries = 2354
Number of mailbox timeouts = 0
Number of ISP aborts = 0
Number of loop resyncs = 0
Number of retries for empty slots = 0
Number of reqs in pending_q= 0, retry_q= 0, done_q= 0, scsi_retry_q= 0
Host adapter:loop state = , flags = 0x5e13
Dpc flags = 0x4080000
MBX flags = 0x0
Link down Timeout = 045
Port down retry = 045
Login retry count = 045
Commands retried with dropped frame(s) = 0
Product ID = 0000 0000 0000 0000
SCSI Device Information:
scsi-qla0-adapter-node=2000001b329757d9;
scsi-qla0-adapter-port=2100001b329757d9;
scsi-qla0-target-0=500a0981894b2d98;
FC Port Information:
scsi-qla0-port-0=500a0980894b2d98:500a0981894b2d98:0000da:0;
SCSI LUN Information:
(Id:Lun) * - indicates lun is not registered with the OS.
( 0: 0): Total reqs 943947321, Pending reqs 1, flags 0x0, 0:0:00 00
( 0: 1): Total reqs 1564855950, Pending reqs 1, flags 0x0, 0:0:00 00
( 0: 5): Total reqs 56482209, Pending reqs 0, flags 0x0, 0:0:00 00
( 0: 6): Total reqs 297127853, Pending reqs 0, flags 0x0, 0:0:00 00
[root@hfdb2 qla2xxx]#
[root@db2 qla2xxx]# cat /proc/scsi/qla2xxx/4
QLogic PCI to Fibre Channel Host Adapter for QLE2460:
Firmware version 4.04.00 [IP] [84XX] , Driver version 8.02.09-d0-rhel4.7-04
ISP: ISP2432
Request Queue = 0x17d9100000, Response Queue = 0x17d90e0000
Request Queue count = 4096, Response Queue count = 512
Total number of active commands = 0
Total number of interrupts = 2402120994
Device queue depth = 0x20
Number of free request entries = 349
Number of mailbox timeouts = 0
Number of ISP aborts = 0
Number of loop resyncs = 0
Number of retries for empty slots = 0
Number of reqs in pending_q= 0, retry_q= 0, done_q= 0, scsi_retry_q= 0
Host adapter:loop state = , flags = 0x5e13
Dpc flags = 0x4080000
MBX flags = 0x0
Link down Timeout = 045
Port down retry = 045
Login retry count = 045
Commands retried with dropped frame(s) = 0
Product ID = 0000 0000 0000 0000
SCSI Device Information:
scsi-qla1-adapter-node=2000001b329741cb;
scsi-qla1-adapter-port=2100001b329741cb;
scsi-qla1-target-0=500a0981994b2d98;
FC Port Information:
scsi-qla1-port-0=500a0980894b2d98:500a0981994b2d98:0000da:0;
SCSI LUN Information:
(Id:Lun) * - indicates lun is not registered with the OS.
( 0: 0): Total reqs 3, Pending reqs 0, flags 0x0*, 1:0:00 00
( 0: 2): Total reqs 1119703118, Pending reqs 0, flags 0x0, 1:0:00 00
( 0: 3): Total reqs 1138077451, Pending reqs 0, flags 0x0, 1:0:00 00
( 0: 4): Total reqs 147824891, Pending reqs 0, flags 0x0, 1:0:00 00
( 0: 7): Total reqs 670637, Pending reqs 0, flags 0x0, 1:0:00 00
[root@db2 qla2xxx]#
[root@db2 qla2xxx]# df -h
Filesystem Size Used Avail Use% Mounted on
/dev/sda2 100G 7.9G 88G 9% /
/dev/sda1 99M 14M 81M 15% /boot
none 48G 0 48G 0% /dev/shm
/dev/sda5 38G 13G 23G 36% /dba
/dev/sda6 1.2T 697G 388G 65% /archive
/dev/sdb1 1.3T 1010G 159G 87% /u01
/dev/sdc1 1.3T 899G 280G 77% /u02
/dev/sdf1 1.3T 804G 384G 68% /u03
/dev/sdg1 1.3T 729G 449G 62% /u04
/dev/sdh5 1000G 467G 484G 50% /u05
/dev/sdd1 1.5T 627G 780G 45% /u06
/dev/sde1 1.5T 1.1T 311G 78% /u07
/dev/sdi1 1020G 94G 875G 10% /u08
[root@db2 qla2xxx]# sfdisk -s
/dev/sda: 1462108160
/dev/sdb: 1310797824
/dev/sdc: 1321318400
/dev/sdd: 1552031744
/dev/sde: 1552031744
/dev/sdf: 1331879936
/dev/sdg: 1321318400
/dev/sdh: 1048689664
/dev/sdi: 1069547520
[root@db2 qla2xxx]# df -i
Filesystem Inodes IUsed IFree IUse% Mounted on
/dev/sda2 13320192 333934 12986258 3% /
/dev/sda1 26104 41 26063 1% /boot
none 12374053 1 12374052 1% /dev/shm
/dev/sda5 5003712 47158 4956554 1% /dba
/dev/sda6 152076288 1487 152074801 1% /archive
/dev/sdb1 163856384 294 163856090 1% /u01
/dev/sdc1 165167104 71 165167033 1% /u02
/dev/sdf1 166494208 74 166494134 1% /u03
/dev/sdg1 165167104 72 165167032 1% /u04
/dev/sdh5 1024128 41 1024087 1% /u05
/dev/sdd1 1515776 121 1515655 1% /u06
/dev/sde1 1515776 113 1515663 1% /u07
/dev/sdi1 1044480 19 1044461 1% /u08
[root@db2 qla2xxx]#
*****************************on host*******10.10.1.11******************************
*****************************on host*******10.10.1.12******************************
joe@ubuntu104:~$ ssh [email protected]
The authenticity of host '10.10.1.14 (10.10.1.14)' can't be established.
RSA key fingerprint is a6:2d:d8:e9:77:22:a9:11:10:5e:65:6b:6d:61:78:5a.
Are you sure you want to continue connecting (yes/no)? yes
Warning: Permanently added '10.10.1.14' (RSA) to the list of known hosts.
[email protected]'s password:
Last login: Mon Jan 24 18:55:51 2011 from hq-it-082147.sf.com
[root(db1)@~]# cat /proc/scsi/qla2xxx/3
QLogic PCI to Fibre Channel Host Adapter for QLE2460:
Firmware version 4.04.00 [IP] [84XX] , Driver version 8.02.09-d0-rhel4.7-04
ISP: ISP2432
Request Queue = 0x11ece80000, Response Queue = 0x11ece30000
Request Queue count = 4096, Response Queue count = 512
Total number of active commands = 0
Total number of interrupts = 2232
Device queue depth = 0x20
Number of free request entries = 3815
Number of mailbox timeouts = 0
Number of ISP aborts = 0
Number of loop resyncs = 0
Number of retries for empty slots = 0
Number of reqs in pending_q= 0, retry_q= 0, done_q= 0, scsi_retry_q= 0
Host adapter:loop state = , flags = 0x5e13
Dpc flags = 0x4080000
MBX flags = 0x0
Link down Timeout = 045
Port down retry = 045
Login retry count = 045
Commands retried with dropped frame(s) = 0
Product ID = 0000 0000 0000 0000
SCSI Device Information:
scsi-qla0-adapter-node=2000001b3290965d;
scsi-qla0-adapter-port=2100001b3290965d;
scsi-qla0-target-0=500a0982894b2d98;
FC Port Information:
scsi-qla0-port-0=500a0980894b2d98:500a0982894b2d98:0000da:0;
SCSI LUN Information:
(Id:Lun) * - indicates lun is not registered with the OS.
( 0: 0): Total reqs 536, Pending reqs 0, flags 0x0, 0:0:00 00
( 0: 1): Total reqs 535, Pending reqs 0, flags 0x0, 0:0:00 00
( 0: 5): Total reqs 535, Pending reqs 0, flags 0x0, 0:0:00 00
( 0: 6): Total reqs 535, Pending reqs 0, flags 0x0, 0:0:00 00
[root(db1)@~]#
[root(db1)@~]# cat /proc/scsi/qla2xxx/4
QLogic PCI to Fibre Channel Host Adapter for QLE2460:
Firmware version 4.04.00 [IP] [84XX] , Driver version 8.02.09-d0-rhel4.7-04
ISP: ISP2432
Request Queue = 0x11ec600000, Response Queue = 0x11ec5f0000
Request Queue count = 4096, Response Queue count = 512
Total number of active commands = 0
Total number of interrupts = 2236
Device queue depth = 0x20
Number of free request entries = 3633
Number of mailbox timeouts = 0
Number of ISP aborts = 0
Number of loop resyncs = 0
Number of retries for empty slots = 0
Number of reqs in pending_q= 0, retry_q= 0, done_q= 0, scsi_retry_q= 0
Host adapter:loop state = , flags = 0x5e13
Dpc flags = 0x4080000
MBX flags = 0x0
Link down Timeout = 045
Port down retry = 045
Login retry count = 045
Commands retried with dropped frame(s) = 0
Product ID = 0000 0000 0000 0000
SCSI Device Information:
scsi-qla1-adapter-node=2000001b32900f5e;
scsi-qla1-adapter-port=2100001b32900f5e;
scsi-qla1-target-0=500a0982994b2d98;
FC Port Information:
scsi-qla1-port-0=500a0980894b2d98:500a0982994b2d98:0000da:0;
SCSI LUN Information:
(Id:Lun) * - indicates lun is not registered with the OS.
( 0: 0): Total reqs 3, Pending reqs 0, flags 0x0*, 1:0:00 00
( 0: 2): Total reqs 535, Pending reqs 0, flags 0x0, 1:0:00 00
( 0: 3): Total reqs 535, Pending reqs 0, flags 0x0, 1:0:00 00
( 0: 4): Total reqs 538, Pending reqs 0, flags 0x0, 1:0:00 00
( 0: 7): Total reqs 535, Pending reqs 0, flags 0x0, 1:0:00 00
[root(db1)@~]# [root(db1)@~]# sfdisk -s
/dev/sda: 1462108160
/dev/sdb: 1310797824
/dev/sdc: 1321318400
/dev/sdd: 1552031744
/dev/sde: 1552031744
/dev/sdf: 1331879936
/dev/sdg: 1321318400
/dev/sdh: 1048689664
/dev/sdi: 1069547520
[root(db1)@~]#