华为与H3C（二）实验

标题 华为与H3C（二）实验案例

作者：王丰 日期：2019.8.5

~# 拓扑图

一 ：rip v2 ，rip汇总

二：ospf多区域，重分发，ospf汇总，ospf身份验证

三：单臂路由

四：开启telnet远程

五：桥接pc访问全网和远程

实验步骤： 分别给r1，r2，r3，r4，配置ip地址和虚拟接口
R1配置ip**
[r1]interface GigabitEthernet 0/0/0
[r1-GigabitEthernet0/0/0]IP address 192.168.10.1 24
配置r1虚拟接口
[r1]interface LoopBack 1
[r1-LoopBack1]ip address 172.16.1.1 255.255.255.0
[r1]inter loo 2
[r1-LoopBack2]ip address 172.16.2.2 255.255.255.0
[r1]inter loo 3
[r1-LoopBack3]ip address 172.16.3.3 255.255.255.0
[r1]inter loo 4
[r1-LoopBack4]ip address 172.16.4.4 255.255.255.0
查看端口状态
[r1]display ip int b

（2）r2配置ip地址
[r2]interface GigabitEthernet 0/0/0
[r2-GigabitEthernet0/0/0]IP address 192.168.10.2 24
[r2]interface GigabitEthernet 0/0/1
[r2-GigabitEthernet0/0/1]IP address 192.168.20.1 24
[r2-GigabitEthernet0/0/1]UNDO shutdown
R2配置虚拟接口
[r2]interface loo 1
[r2-LoopBack1]ip address 1.1.1.1 32
查看端口状态**

R3配置ip地址
[r3]interface GigabitEthernet 0/0/0
[r3-GigabitEthernet0/0/0]ip address 192.168.20.2 24
[r3]interface GigabitEthernet 0/0/1
[r3-GigabitEthernet0/0/1]ip address 192.168.30.1 24
[r3-GigabitEthernet0/0/1]undo shutdown
配置虚拟接口
[r3]interface loo 1
[r3-LoopBack1]ip address 2.2.2.2 32
查看端口状态

R4配置ip地址
[r4]interface GigabitEthernet 0/0/0
[r4-GigabitEthernet0/0/0]ip address 192.168.30.2 24
[r4]interface GigabitEthernet 0/0/1
[r4-GigabitEthernet0/0/1]ip address 192.168.40.1 24
[r4-GigabitEthernet0/0/1]undo shutdown
R4配置虚拟接口ip地址
[r4]interface LOO 1
[r4-LoopBack1]ip address 3.3.3.3 32
查看端口状态

配置pc1和pc3的ip地址网关，


（2）SW1创建vlan配置trunk
[sw1]vlan batch 10 20
[sw1]interface GigabitEthernet 0/0/1
[sw1-GigabitEthernet0/0/1]port link-type trunk
[sw1-GigabitEthernet0/0/1]port trunk allow-pass vlan all
（3）将接口加入vlan
[sw1]interface Ethernet 0/0/1
[sw1-Ethernet0/0/1]port link-type access
[sw1-Ethernet0/0/1]port default vlan 10
[sw1]interface Ethernet 0/0/2
[sw1-Ethernet0/0/2]port link-type access
[sw1-Ethernet0/0/2]port default vlan 20
（4）配置子接口
[r2]interface GigabitEthernet 0/0/2.10
[r2-GigabitEthernet0/0/2.10]arp broadcast enable
[r2-GigabitEthernet0/0/2.10]dot1q termination vid 10
[r2-GigabitEthernet0/0/2.10]ip address 192.168.1.10 24
[r2]interface GigabitEthernet 0/0/2.20
[r2-GigabitEthernet0/0/2.20]ARP broadcast en
[r2-GigabitEthernet0/0/2.20]dot1q termination vid 20
[r2-GigabitEthernet0/0/2.20]ip address 192.168.2.10 24
查看端口状态

配置ospf的宣告直连路由
[r2]ospf router-id 1.1.1.1
[r2-ospf-1]area 0
[r2-ospf-1-area-0.0.0.0]network 1.1.1.1 0.0.0.0
[r2-ospf-1-area-0.0.0.0]network 192.168.20.0 0.0.0.255
[r2-ospf-1-area-0.0.0.0]network 192.168.1.0 0.0.0.255
[r2-ospf-1-area-0.0.0.0]network 192.168.2.0 0.0.0.255
[r2-ospf-1-area-0.0.0.0]network 192.168.0.0 0.0.0.255
[r3]ospf 1 router-id 2.2.2.2
[r3-ospf-1]area 0
[r3-ospf-1-area-0.0.0.0]network 2.2.2.2 0.0.0.0
[r3-ospf-1-area-0.0.0.0]network 192.168.20.0 0.0.0.255
[r3-ospf-1]area 1
[r3-ospf-1-area-0.0.0.1]network 2.2.2.2 0.0.0.0
[r3-ospf-1-area-0.0.0.1]network 192.168.30.0 0.0.0.255
[r4]ospf router-id 3.3.3.3
[r4-ospf-1]area 1
[r4-ospf-1-area-0.0.0.1]network 3.3.3.3 0.0.0.0
[r4-ospf-1-area-0.0.0.1]network 192.168.30.0 0.0.0.255
（2）配置ospf直连路由
[r4]ospf 1
[r4-ospf-1]import-route direct type 2
[r2]ospf 1
[r2-ospf-1]import-route direct type 2
查看是否学习到

配置RIP v2
（1） r1宣告直连
[r1]rip 1
[r1-rip-1]version 2
[r1-rip-1]network 192.168.10.0
[r1-rip-1]network 172.16.0.0
（2） R2宣告直连
[r2]rip 1
[r2-rip-1]version 2
[r2-rip-1]network 192.168.10.0
[r2-rip-1]network 192.168.20.0
（3） 配置R1 0/0/0接口路由rip汇总
[r1]interface GigabitEthernet 0/0/0
[r1-GigabitEthernet0/0/0]rip summary-address 172.16.0.0 255.255.255.0
（4） 将RIP发布到ospf中，将ospf发布到rip中
[r2]ospf 1
[r2-ospf-1]import-route rip cost 1
[r2]rip 1
[r2-rip-1]import-route ospf cost 1

** 桥接pc访问全网和远程
桥接pc**

全网互通
Ping 192.168.20.1

Ping 192.168.10.1

Ping 192.168.1.10

ping192.168.2.10

ping172.16.1.1

ping172.16.2.2

ping172.16.3.3

远程tenlet登录到R1,R2,R3,R4路由器
Tenlet R2 192.168.10.2

Tenlet R3 192.168.20.2

Tenlet R4192.168.30.2

Tenlet R1 192.168.10.1