路由交换笔记（38）--NBMA网络帧中继交换机配置

转自 http://liyongxian.blog.51cto.com/432519/138954 先对FR交换机进行配置   ----FRsw FRsw(config)#frame-relay switching          开启帧中继交换功能 FRsw(config)#interface s0/0 FRsw(config-if)#no shutdown                               FRsw(config-if)#no ip address                       关闭接口IP地址 FRsw(config-if)#encapsulation frame-relay     封闭帧中继 FRsw(config-if)#frame-relay lmi-type cisco    配置LMI类型 FRsw(config-if)#frame-relay intf-type dce      配置接口类型 FRsw(config-if)#clock rate 64000                  配置时钟频率 FRsw(config-if)#frame-relay route 102 interface s0/1 201 FRsw(config-if)#frame-relay route 103 interface s0/2 301 配置该本地端口DLCI值及虚链路对应出口和对端DLCI值 FRsw(config-if)#exit   -------------------------------语句说明参考S0/0接口配置 FRsw(config)#interface s0/1 FRsw(config-if)#no shutdown FRsw(config-if)#no ip address FRsw(config-if)#encapsulation frame-relay FRsw(config-if)#frame-relay lmi-type cisco FRsw(config-if)#frame-relay intf-type dce FRsw(config-if)#clock rate 64000 FRsw(config-if)#frame-relay route 201 interface s0/0 102 FRsw(config-if)#frame-relay route 203 interface s0/2 302 FRsw(config-if)#exit   -------------------------------语句说明参考S0/0接口配置 FRsw(config)#interface s0/2 FRsw(config-if)#no shutdown FRsw(config-if)#no ip address FRsw(config-if)#encapsulation frame-relay FRsw(config-if)#frame-relay lmi-type cisco FRsw(config-if)#frame-relay intf-type dce FRsw(config-if)#clock rate 64000 FRsw(config-if)#frame-relay route 301 interface s0/0 103 FRsw(config-if)#frame-relay route 302 interface s0/1 203 FRsw(config-if)#exit   查看PVC链路状态 #show frame-relay route 由于串行链路上的对端还未进行配置及联接,PVC链路还处于未激活状态.   下面进行DTE端路由器配置 ----R1 R1(config)#interface s0/0 R1(config-if)#ip address 192.168.1.1 255.255.255.0 R1(config-if)#no shutdown R1(config-if)#encapsulation frame-relay      接口封装帧中继 R1(config-if)#no frame-relay inverse-arp    关闭反向ARP            R1(config-if)#frame-relay map ip 192.168.1.2 102 broadcast R1(config-if)#frame-relay map ip 192.168.1.3 103 broadcast                                             配置对端IP与本地DLCI映射   ----R2(语句说明参考R1) R2(config)#interface s0/0 R2(config-if)#ip address 192.168.1.2 255.255.255.0 R2(config-if)#no shutdown R2(config-if)#encapsulation frame-relay R2(config-if)#no frame-relay inverse-arp R2(config-if)#frame-relay map ip 192.168.1.1 201 broadcast R2(config-if)#frame-relay map ip 192.168.1.3 203 broadcast   ----R3(语句说明参考R1) R3(config)#interface s0/0 R3(config-if)#ip address 192.168.1.3 255.255.255.0 R3(config-if)#no shutdown R3(config-if)#encapsulation frame-relay R3(config-if)#no frame-relay inverse-arp R3(config-if)#frame-relay map ip 192.168.1.1 301 broadcast R3(config-if)#frame-relay map ip 192.168.1.2 302 broadcast