Ubuntu网络network eth0配置 | ubuntu network configuration
本文首发于个人博客https://kezunlin.me/post/5076bc45/，欢迎阅读!
ubuntu network configuration
Guide
network proxy
- System wide: Network--->None/Manual
- chrome: can not set
- firefox: about:preferences---> Network Proxy
eth0 config
rename xxx to eth0
errors may occur:
Ubuntu networking restart | cannot find device 'eth0'check eth0
$ dmesg | grep eth [5.715564] e1000 0000:02:01.0 eth0: (PCI:66MHz:32-bit) 00:0c:29:7d:bf:43
[5.715573] e1000 0000:02:01.0 eth0: Intel(R) PRO/1000 Network Connection
[5.719709] e1000 0000:02:01.0 ens33: renamed from eth0and we get ens33 renamed from eth0, we need to change it back to eth0.
solution
(1). edit grub and update
$ sudo vim /etc/default/grub #GRUB_CMDLINE_LINUX=""
GRUB_CMDLINE_LINUX="net.ifnames=0 biosdevname=0" $ sudo update-grub(2) edit network interfaces
auto lo
iface lo inet loopback auto eth0
iface eth0 inet static
address 192.168.1.77
netmask 255.255.255.0
gateway 192.168.1.1 (3) reboot
sudo reboot now(4) check eth0
$ sudo ifconfig eth0 Link encap:Ethernet HWaddr 80:fa:5b:47:92:8a
inet addr:192.168.1.77 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:4640 errors:0 dropped:0 overruns:0 frame:0
TX packets:4640 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:865530 (865.5 KB) TX bytes:865530 (865.5 KB) wlan0 Link encap:Ethernet HWaddr b0:35:9f:53:68:c6
inet addr:192.168.0.130 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::a3d7:e190:6fb3:133/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:6536 errors:0 dropped:0 overruns:0 frame:0
TX packets:380 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:581427 (581.4 KB) TX bytes:46439 (46.4 KB)OK. Now we get eth0,wlan0 properly set.
Reference
- ubuntu rename eth0
History
- 20180108: created
- 20180222: add eth0 part.
Copyright
- Post author: kezunlin
- Post link: https://kezunlin.me/post/5076bc45/
- Copyright Notice: All articles in this blog are licensed under CC BY-NC-SA 3.0 unless stating additionally.