手把手带你实现SDRAM控制器（带Verilog代码）
上篇博客，我们了解了SDRAM的控制命令以及寻址方式，SDRAM芯片需要配合专门的控制电路使用才能发挥功能，这一节我们将一步步分析，使用Verilog搭建一个SDRAM驱动控制器。
目录
学习目标
问题分析
初始化模块
信息收集
模块接口确定
状态机设计
仿真测试
Modelsim仿真：
学习目标
- 搭建SDRAM控制器，能读，能写，并且可以自动初始化以及自动刷新。
- 学习分析问题和使用Verilog解决问题的方法。
问题分析
数字系统自顶向下的的设计原则，我们首先可以分析目标中的功能。不难看出SDRAM控制器应该包含以下模块：
- 初始化模块
- 读控制模块
- 写控制模块
- 自动刷新模块
各个模块将复用SDRAM顶层模块的输出接口，因此将会存在一个总线仲裁的问题，例如当自刷新模块和读模块同时发出请求时，而我们只能响应其中一个，所以我们解决把输出接口交给谁的问题，因此引出第五个模块：仲裁模块。
为了验证设计的需要，我们设计的模块接口兼容野火电子的测试平台接口，各部分关系图如下：
初始化模块
SDRAM在上电之后，在执行正常操作之前需要先执行一次初始化操作。
初始化的流程都是固定的，查看参考手册给的信息可以确定初始化需要顺序执行以下操作：
- 给SDRAM上电，CKE设置为高电平，加载稳定的时钟。
- 执行空指令，并且持续100us。
- 100us过后执行预充电指令，并选中所有Bank（A10为高电平）。
- 预充电指令写入后，等待tRP时间，写入自动刷新命令。
- 之后保持空命令，持续tRC时间。
- tRC时间过后，在此写入自动刷新命令。
- 自动刷新命令写入后，写入空操作命令持续tRC时间。
- 等待时间结束后，即可写入模式寄存器配置指令，地址总线 A0-A11 参数不同 辅助模式寄存器不同模式的设置。
- 模式寄存器配置指令写入后，还需要保持空操 作命令持续 tMRD 时间。
- tMRD时间过后，SDRAM初始化即完成。
观察上述步骤，我们的脑海中肯定一直回荡着：计数器~、状态机~ ，对的，是这样的，完全没错！这个模块的设计主要就是围绕 状态机，佐以计数器。
抛开状态机细节不谈，我们下一步应该要收集我们需要的资料信息：
信息收集
- 时钟资源：100MHz系统时钟，一个周期就是10us
- T=100us 为最小等待时间，我们在使用 SDRAM 时，等待时间 T 可适当延长，设定为200us。
- 开发板的SDRAM信号为W9825G6KH，tRP为两个时钟周期，tMRD3个时钟周期，tRC7个时钟周期。
- 初始化过程中，至少进行两次自动刷新，也可适当增加刷新次数，设定为8次。
- 使用的命令集：NOP=4‘b0111，P_CHARGE=4’b0010，AUTO_REF = 4'b0001,M_REG_SET= 4'b0000。
模块接口确定
本状态机属于穆尔型状态机，时钟和复位接口作为仅有的两个输入，输出则根据SDRAM命令集接口有 init_cmd (4bit) 、init_ba（Bank辅助，2bit），init_addr（地址辅助，13bit），init_end（完成信号，1bit）
状态机设计
状态机的设计有三大要素需要考虑：1、状态数目，2、状态转移条件，3、状态输出。
首先我们要设计出状态的数目，我们可以由前面的初始化步骤画出我们的状态转移图：
平板太滑了，展现不出本人的书法水平，所以大家将就着看。
可以看到，我们的状态机可以设计9个状态去实现它，可能有同学会问，为什么等待状态也要设置好几个不同的状态呀？能不能只设计一个？这是个好问题，其实这四个等待状态就相当于一个等待状态，我们的计数器也只设计一个，然后每个状态会传递不同的计数周期参数，并在计数完成时清零。当然也不是不可以每个状态设计一个计数器，这样代码会简单很多，其实我也建议大家这样做，我觉得Verilog代码设计思路越简单越好，不要像带着C语言那样一个main走天下的思路去写Verilog。
接下来就是代码实现：
// 刷新模块 New_Designed By BUCT WWD 2022/9/7
// SDRAM初始化模块，初始化步骤：上电--延时200us--预充电--刷新x8--寄存器设定--完成
module sdram_init(
input wire sys_clk, //系统时钟信号
input wire sys_rst_n,//系统复位信号
output wire[1:0] init_ba, //Bank辅助位
output wire[3:0] init_cmd,//命令位
output wire[12:0] init_addr,//地址辅助位
output wire init_end //初始化结束标志
);
parameter IDLE = 4'd0,Wait1 = 4'd1,P_CHAR = 4'd2,Wait2 =4'd3,Auto_REF=4'd4,Wait3=4'd5,MRS=4'd6,Wait4=4'd7,OK=4'd8;//九个状态
parameter Init_t = 15'd20000,//初始化200us，各项等待参数
TRP_t = 15'd2,
TRC_t = 15'd7,
TMRD_t = 15'd3;
parameter P_CHARGE = 4'b0010, //指令集
Au_REF = 4'b0001,
NOP = 4'b0111,
M_REG_SET = 4'b0000;
parameter REF_TIME = 4'd8; //自刷新次数参数
reg[3:0] state,next_state;
reg[14:0] cnt_now; //延时长度寄存器
reg[14:0] cnt_value; //计时计数器值
reg[3:0] REF_cnt; //刷新计数
reg[1:0] init_ba_reg;
reg[3:0] init_cmd_reg;
reg[12:0] init_addr_reg;
reg init_end_reg;
always@(posedge sys_clk or negedge sys_rst_n)begin//状态转移
if(sys_rst_n ==1'b0)
state <= IDLE;
else
state <= next_state;
end
always@(posedge sys_clk or negedge sys_rst_n)begin//计时器模块
if(sys_rst_n ==1'b0)
cnt_value <= 15'd0;
else if(cnt_value == cnt_now)//计满自动清零
cnt_value <= 15'd0;
else
cnt_value <= cnt_value +15'd1;
end
always@(posedge sys_clk or negedge sys_rst_n)begin //刷新次数计数器
if(sys_rst_n ==1'b0)
REF_cnt <= 4'd0;
else if((REF_cnt == REF_TIME)&&(cnt_value == 15'd7))
REF_cnt <= 4'd0;
else if(next_state==Auto_REF)
REF_cnt <= REF_cnt + 4'd1;
else
REF_cnt <= REF_cnt;
end
always@(*)begin //状态转移判断模块，根据计时时间判断是否已经持续相应时间长度
if(sys_rst_n ==1'b0)begin
next_state = IDLE;
end else begin
case(state)
IDLE: next_state = Wait1;
Wait1:if(cnt_value == cnt_now)
next_state = P_CHAR;
else
next_state = state;
P_CHAR:next_state = Wait2;
Wait2:if(cnt_value == cnt_now)
next_state = Auto_REF;
else
next_state = state;
Auto_REF:next_state = Wait3;
Wait3:if((REF_cnt == REF_TIME)&&(cnt_value == cnt_now))//自刷新的转移条件还要满足重复次数
next_state = MRS;
else if(cnt_value == cnt_now)
next_state = Auto_REF;
else
next_state = state;
MRS:next_state = Wait4;
Wait4:if(cnt_value==cnt_now)
next_state = OK;
else
next_state = state;
OK: next_state =OK;
endcase
end
end
always@(posedge sys_clk or negedge sys_rst_n)begin
/*各个state持续时间只的设定，特点：时序模块，由下一个状态判断，
这样，在切换状态的一瞬间，计数器执行清零操作，目标计数值被重新赋值，这样就实现了延时参数的传递*/
if(sys_rst_n ==1'b0)begin
cnt_now <= 15'd0;
end else begin
case(next_state)
IDLE:cnt_now <= 15'd0;
Wait1: cnt_now <= Init_t;
P_CHAR:cnt_now <= 15'd0;
Wait2:cnt_now <= TRP_t;
Auto_REF:cnt_now <= 15'd0;
Wait3:cnt_now <= TRC_t;
MRS:cnt_now <= 15'd0;
Wait4:cnt_now <= TMRD_t;
OK:cnt_now <=15'd0;
endcase
end
end
always@(posedge sys_clk or negedge sys_rst_n)begin //输出模块，三段式状态机
if(sys_rst_n == 1'b0)begin
init_cmd_reg <= NOP;
init_ba_reg <= 2'b11;
init_addr_reg <= 13'h1fff;
init_end_reg <= 1'b0;
end else
case(next_state)
IDLE,Wait1,Wait2,Wait3,Wait4: begin
init_cmd_reg <= NOP;
init_ba_reg <= 2'b11;
init_addr_reg <= 13'h1fff;
end
P_CHAR:begin
init_cmd_reg <= P_CHARGE;
init_ba_reg <= 2'b11;
init_addr_reg <= 13'h1fff;
end
Auto_REF:begin
init_cmd_reg <= Au_REF;
init_ba_reg <= 2'b11;
init_addr_reg <= 13'h1fff;
end
MRS:begin
init_cmd_reg <= M_REG_SET;
init_ba_reg <= 2'b00;
init_addr_reg <=
{ //地址辅助配置模式寄存器,参数不同,配置的模式不同
3'b000,//A12-A10:预留
1'b0, //A9=0:读写方式,0:突发读&突发写,1:突发读&单写
2'b00, //{A8,A7}=00:标准模式,默认
3'b011,//{A6,A5,A4}=011:CAS 潜伏期,010:2,011:3,其他:保留
1'b0, //A3=0:突发传输方式,0:顺序,1:隔行
3'b111 //{A2,A1,A0}=111:突发长度,000:单字节,001:2 字节
//010:4 字节,011:8 字节,111:整页,其他:保留
};
end
OK:begin
init_cmd_reg <= NOP;
init_ba_reg <= 2'b11;
init_addr_reg <= 13'h1fff;
init_end_reg <= 1'b1;
end
endcase
end
//最后由于输出是线网，因此需要连续赋值
assign init_cmd = init_cmd_reg;
assign init_addr = init_addr_reg;
assign init_ba = init_ba_reg;
assign init_end = init_end_reg;
endmodule我写的这个状态机有几个特点，第一采用变量少，第二采用的计数器少，第三逻辑简单，大家可以好好体会一下如何让状态机的状态延长时间的方法。事实上我们可以发现，初始化模块所要求的延时都为时钟周期的整数，并且不会有同时两个延时，整个模块的计数器只有两个：自刷新计数器和延时计数器。我们只需要在每个状态来临时赋给它们相应的计数参数，就可以实现单计数器，多状态共用。
仿真测试
TB文件
为了验证我们的状态机设计，我们采用野火的验证平台，这次的测试工程共包含三个部分：
- sdram_init.v
- tb_sdram.v
- sdram_model_plus.v //sdram模块模拟
- PLL IP核
`timescale 1ns/1ns
// Author : EmbedFire
// Create Date : 2019/08/25
// Module Name : tb_sdram_init
// Project Name : uart_sdram
// Target Devices: Altera EP4CE10F17C8N
// Tool Versions : Quartus 13.0
// Description : SDRAM初始化模块仿真
//
// Revision : V1.0
// Additional Comments:
//
// 实验平台: 野火_征途Pro_FPGA开发板
// 公司 : http://www.embedfire.com
// 论坛 : http://www.firebbs.cn
// 淘宝 : https://fire-stm32.taobao.com
module tb_sdram_init();
//********************************************************************//
//****************** Internal Signal and Defparam ********************//
//********************************************************************//
//wire define
//clk_gen
wire clk_50m ; //PLL输出50M时钟
wire clk_100m ; //PLL输出100M时钟
wire clk_100m_shift ; //PLL输出100M时钟,相位偏移-30deg
wire locked ; //PLL时钟锁定信号
wire rst_n ; //复位信号,低有效
//sdram_init
wire [3:0] init_cmd ; //初始化阶段指令
wire [1:0] init_ba ; //初始化阶段L-Bank地址
wire [12:0] init_addr ; //初始化阶段地址总线
wire init_end ; //初始化完成信号
//reg define
reg sys_clk ; //系统时钟
reg sys_rst_n ; //复位信号
//defparam
//重定义仿真模型中的相关参数
defparam sdram_model_plus_inst.addr_bits = 13; //地址位宽
defparam sdram_model_plus_inst.data_bits = 16; //数据位宽
defparam sdram_model_plus_inst.col_bits = 9; //列地址位宽
defparam sdram_model_plus_inst.mem_sizes = 2*1024*1024; //L-Bank容量
//********************************************************************//
//**************************** Clk And Rst ***************************//
//********************************************************************//
//时钟、复位信号
initial
begin
sys_clk = 1'b1 ;
sys_rst_n <= 1'b0 ;
#200
sys_rst_n <= 1'b1 ;
end
always #10 sys_clk = ~sys_clk;
//rst_n:复位信号
assign rst_n = sys_rst_n & locked;
//********************************************************************//
//*************************** Instantiation **************************//
//********************************************************************//
//------------- clk_gen_inst -------------
clk_gen clk_gen_inst (
.inclk0 (sys_clk ),
.areset (~sys_rst_n ),
.c0 (clk_50m ),
.c1 (clk_100m ),
.c2 (clk_100m_shift ),
.locked (locked )
);
//------------- sdram_init_inst -------------
sdram_init sdram_init_inst(
.sys_clk (clk_100m ),
.sys_rst_n (rst_n ),
.init_cmd (init_cmd ),
.init_ba (init_ba ),
.init_addr (init_addr ),
.init_end (init_end )
);
//-------------sdram_model_plus_inst-------------
sdram_model_plus sdram_model_plus_inst(
.Dq ( ),
.Addr (init_addr ),
.Ba (init_ba ),
.Clk (clk_100m_shift ),
.Cke (1'b1 ),
.Cs_n (init_cmd[3] ),
.Ras_n (init_cmd[2] ),
.Cas_n (init_cmd[1] ),
.We_n (init_cmd[0] ),
.Dqm (2'b0 ),
.Debug (1'b1 )
);
endmodulesdram_model
/***************************************************************************************
作者： 李晟
2003-08-27 V0.1 李晟
添加内存模块倒空功能，在外部需要创建事件：sdram_r ,本SDRAM的内容将会按Bank 顺序damp out 至文件
sdram_data.txt 中
×××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××××*/
//2004-03-04 陈乃奎 修改原程序中将BANK的数据转存入TXT文件的格式
//2004-03-16 陈乃奎 修改SDRAM 的初始化数据
//2004/04/06 陈乃奎 将SDRAM的操作命令以字符形式表示，以便用MODELSIM监视
//2004/04/19 陈乃奎 修改参数 parameter tAC = 8;
//2010/09/17 罗瑶 修改sdram的大小，数据位宽，dqm宽度;
/****************************************************************************************
*
* File Name: sdram_model.V
* Version: 0.0f
* Date: July 8th, 1999
* Model: BUS Functional
* Simulator: Model Technology (PC version 5.2e PE)
*
* Dependencies: None
*
* Author: Son P. Huynh
* Email: [email protected]
* Phone: (208) 368-3825
* Company: Micron Technology, Inc.
* Model: sdram_model (1Meg x 16 x 4 Banks)
*
* Description: 64Mb SDRAM Verilog model
*
* Limitation: - Doesn't check for 4096 cycle refresh
*
* Note: - Set simulator resolution to "ps" accuracy
* - Set Debug = 0 to disable $display messages
*
* Disclaimer: THESE DESIGNS ARE PROVIDED "AS IS" WITH NO WARRANTY
* WHATSOEVER AND MICRON SPECIFICALLY DISCLAIMS ANY
* IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR
* A PARTICULAR PURPOSE, OR AGAINST INFRINGEMENT.
*
* Copyright ?1998 Micron Semiconductor Products, Inc.
* All rights researved
*
* Rev Author Phone Date Changes
* ---- ---------------------------- ---------- ---------------------------------------
* 0.0f Son Huynh 208-368-3825 07/08/1999 - Fix tWR = 1 Clk + 7.5 ns (Auto)
* Micron Technology Inc. - Fix tWR = 15 ns (Manual)
* - Fix tRP (Autoprecharge to AutoRefresh)
*
* 0.0a Son Huynh 208-368-3825 05/13/1998 - First Release (from 64Mb rev 0.0e)
* Micron Technology Inc.
****************************************************************************************/
`timescale 1ns / 100ps
module sdram_model_plus (Dq, Addr, Ba, Clk, Cke, Cs_n, Ras_n, Cas_n, We_n, Dqm,Debug);
parameter addr_bits = 11;
parameter data_bits = 32;
parameter col_bits = 8;
parameter mem_sizes = 1048576*2-1;//1 Meg
inout [data_bits - 1 : 0] Dq;
input [addr_bits - 1 : 0] Addr;
input [1 : 0] Ba;
input Clk;
input Cke;
input Cs_n;
input Ras_n;
input Cas_n;
input We_n;
input [3 : 0] Dqm; //高低各8bit
//added by xzli
input Debug;
reg [data_bits - 1 : 0] Bank0 [0 : mem_sizes];//存储器类型数据
reg [data_bits - 1 : 0] Bank1 [0 : mem_sizes];
reg [data_bits - 1 : 0] Bank2 [0 : mem_sizes];
reg [data_bits - 1 : 0] Bank3 [0 : mem_sizes];
reg [1 : 0] Bank_addr [0 : 3]; // Bank Address Pipeline
reg [col_bits - 1 : 0] Col_addr [0 : 3]; // Column Address Pipeline
reg [3 : 0] Command [0 : 3]; // Command Operation Pipeline
reg [3 : 0] Dqm_reg0, Dqm_reg1; // DQM Operation Pipeline
reg [addr_bits - 1 : 0] B0_row_addr, B1_row_addr, B2_row_addr, B3_row_addr;
reg [addr_bits - 1 : 0] Mode_reg;
reg [data_bits - 1 : 0] Dq_reg, Dq_dqm;
reg [col_bits - 1 : 0] Col_temp, Burst_counter;
reg Act_b0, Act_b1, Act_b2, Act_b3; // Bank Activate
reg Pc_b0, Pc_b1, Pc_b2, Pc_b3; // Bank Precharge
reg [1 : 0] Bank_precharge [0 : 3]; // Precharge Command
reg A10_precharge [0 : 3]; // Addr[10] = 1 (All banks)
reg Auto_precharge [0 : 3]; // RW AutoPrecharge (Bank)
reg Read_precharge [0 : 3]; // R AutoPrecharge
reg Write_precharge [0 : 3]; // W AutoPrecharge
integer Count_precharge [0 : 3]; // RW AutoPrecharge (Counter)
reg RW_interrupt_read [0 : 3]; // RW Interrupt Read with Auto Precharge
reg RW_interrupt_write [0 : 3]; // RW Interrupt Write with Auto Precharge
reg Data_in_enable;
reg Data_out_enable;
reg [1 : 0] Bank, Previous_bank;
reg [addr_bits - 1 : 0] Row;
reg [col_bits - 1 : 0] Col, Col_brst;
// Internal system clock
reg CkeZ, Sys_clk;
reg [21:0] dd;
// Commands Decode
wire Active_enable = ~Cs_n & ~Ras_n & Cas_n & We_n;
wire Aref_enable = ~Cs_n & ~Ras_n & ~Cas_n & We_n;
wire Burst_term = ~Cs_n & Ras_n & Cas_n & ~We_n;
wire Mode_reg_enable = ~Cs_n & ~Ras_n & ~Cas_n & ~We_n;
wire Prech_enable = ~Cs_n & ~Ras_n & Cas_n & ~We_n;
wire Read_enable = ~Cs_n & Ras_n & ~Cas_n & We_n;
wire Write_enable = ~Cs_n & Ras_n & ~Cas_n & ~We_n;
// Burst Length Decode
wire Burst_length_1 = ~Mode_reg[2] & ~Mode_reg[1] & ~Mode_reg[0];
wire Burst_length_2 = ~Mode_reg[2] & ~Mode_reg[1] & Mode_reg[0];
wire Burst_length_4 = ~Mode_reg[2] & Mode_reg[1] & ~Mode_reg[0];
wire Burst_length_8 = ~Mode_reg[2] & Mode_reg[1] & Mode_reg[0];
// CAS Latency Decode
wire Cas_latency_2 = ~Mode_reg[6] & Mode_reg[5] & ~Mode_reg[4];
wire Cas_latency_3 = ~Mode_reg[6] & Mode_reg[5] & Mode_reg[4];
// Write Burst Mode
wire Write_burst_mode = Mode_reg[9];
wire Debug; // Debug messages : 1 = On; 0 = Off
wire Dq_chk = Sys_clk & Data_in_enable; // Check setup/hold time for DQ
reg [31:0] mem_d;
event sdram_r,sdram_w,compare;
assign Dq = Dq_reg; // DQ buffer
// Commands Operation
`define ACT 0
`define NOP 1
`define READ 2
`define READ_A 3
`define WRITE 4
`define WRITE_A 5
`define PRECH 6
`define A_REF 7
`define BST 8
`define LMR 9
// // Timing Parameters for -75 (PC133) and CAS Latency = 2
// parameter tAC = 8; //test 6.5
// parameter tHZ = 7.0;
// parameter tOH = 2.7;
// parameter tMRD = 2.0; // 2 Clk Cycles
// parameter tRAS = 44.0;
// parameter tRC = 66.0;
// parameter tRCD = 20.0;
// parameter tRP = 20.0;
// parameter tRRD = 15.0;
// parameter tWRa = 7.5; // A2 Version - Auto precharge mode only (1 Clk + 7.5 ns)
// parameter tWRp = 0.0; // A2 Version - Precharge mode only (15 ns)
// Timing Parameters for -7 (PC143) and CAS Latency = 3
parameter tAC = 6.5; //test 6.5
parameter tHZ = 5.5;
parameter tOH = 2;
parameter tMRD = 2.0; // 2 Clk Cycles
parameter tRAS = 48.0;
parameter tRC = 70.0;
parameter tRCD = 20.0;
parameter tRP = 20.0;
parameter tRRD = 14.0;
parameter tWRa = 7.5; // A2 Version - Auto precharge mode only (1 Clk + 7.5 ns)
parameter tWRp = 0.0; // A2 Version - Precharge mode only (15 ns)
// Timing Check variable
integer MRD_chk;
integer WR_counter [0 : 3];
time WR_chk [0 : 3];
time RC_chk, RRD_chk;
time RAS_chk0, RAS_chk1, RAS_chk2, RAS_chk3;
time RCD_chk0, RCD_chk1, RCD_chk2, RCD_chk3;
time RP_chk0, RP_chk1, RP_chk2, RP_chk3;
integer test_file;
//*****display the command of the sdram**************************************
parameter Mode_Reg_Set =4'b0000;
parameter Auto_Refresh =4'b0001;
parameter Row_Active =4'b0011;
parameter Pre_Charge =4'b0010;
parameter PreCharge_All =4'b0010;
parameter Write =4'b0100;
parameter Write_Pre =4'b0100;
parameter Read =4'b0101;
parameter Read_Pre =4'b0101;
parameter Burst_Stop =4'b0110;
parameter Nop =4'b0111;
parameter Dsel =4'b1111;
wire [3:0] sdram_control;
reg cke_temp;
reg [8*13:1] sdram_command;
always@(posedge Clk)
cke_temp<=Cke;
assign sdram_control={Cs_n,Ras_n,Cas_n,We_n};
always@(sdram_control or cke_temp)
begin
case(sdram_control)
Mode_Reg_Set: sdram_command<="Mode_Reg_Set";
Auto_Refresh: sdram_command<="Auto_Refresh";
Row_Active: sdram_command<="Row_Active";
Pre_Charge: sdram_command<="Pre_Charge";
Burst_Stop: sdram_command<="Burst_Stop";
Dsel: sdram_command<="Dsel";
Write: if(cke_temp==1)
sdram_command<="Write";
else
sdram_command<="Write_suspend";
Read: if(cke_temp==1)
sdram_command<="Read";
else
sdram_command<="Read_suspend";
Nop: if(cke_temp==1)
sdram_command<="Nop";
else
sdram_command<="Self_refresh";
default: sdram_command<="Power_down";
endcase
end
//*****************************************************
initial
begin
//test_file=$fopen("test_file.txt");
end
initial
begin
Dq_reg = {data_bits{1'bz}};
{Data_in_enable, Data_out_enable} = 0;
{Act_b0, Act_b1, Act_b2, Act_b3} = 4'b0000;
{Pc_b0, Pc_b1, Pc_b2, Pc_b3} = 4'b0000;
{WR_chk[0], WR_chk[1], WR_chk[2], WR_chk[3]} = 0;
{WR_counter[0], WR_counter[1], WR_counter[2], WR_counter[3]} = 0;
{RW_interrupt_read[0], RW_interrupt_read[1], RW_interrupt_read[2], RW_interrupt_read[3]} = 0;
{RW_interrupt_write[0], RW_interrupt_write[1], RW_interrupt_write[2], RW_interrupt_write[3]} = 0;
{MRD_chk, RC_chk, RRD_chk} = 0;
{RAS_chk0, RAS_chk1, RAS_chk2, RAS_chk3} = 0;
{RCD_chk0, RCD_chk1, RCD_chk2, RCD_chk3} = 0;
{RP_chk0, RP_chk1, RP_chk2, RP_chk3} = 0;
$timeformat (-9, 0, " ns", 12);
//$readmemh("bank0.txt", Bank0);
//$readmemh("bank1.txt", Bank1);
//$readmemh("bank2.txt", Bank2);
//$readmemh("bank3.txt", Bank3);
/*
for(dd=0;dd<=mem_sizes;dd=dd+1)
begin
Bank0[dd]=dd[data_bits - 1 : 0];
Bank1[dd]=dd[data_bits - 1 : 0]+1;
Bank2[dd]=dd[data_bits - 1 : 0]+2;
Bank3[dd]=dd[data_bits - 1 : 0]+3;
end
*/
initial_sdram(0);
end
task initial_sdram;
input data_sign;
reg [3:0] data_sign;
for(dd=0;dd<=mem_sizes;dd=dd+1)
begin
mem_d = {data_sign,data_sign,data_sign,data_sign,data_sign,data_sign,data_sign,data_sign};
if(data_bits==16)
begin
Bank0[dd]=mem_d[15:0];
Bank1[dd]=mem_d[15:0];
Bank2[dd]=mem_d[15:0];
Bank3[dd]=mem_d[15:0];
end
else if(data_bits==32)
begin
Bank0[dd]=mem_d[31:0];
Bank1[dd]=mem_d[31:0];
Bank2[dd]=mem_d[31:0];
Bank3[dd]=mem_d[31:0];
end
end
endtask
// System clock generator
always
begin
@(posedge Clk)
begin
Sys_clk = CkeZ;
CkeZ = Cke;
end
@(negedge Clk)
begin
Sys_clk = 1'b0;
end
end
always @ (posedge Sys_clk) begin
// Internal Commamd Pipelined
Command[0] = Command[1];
Command[1] = Command[2];
Command[2] = Command[3];
Command[3] = `NOP;
Col_addr[0] = Col_addr[1];
Col_addr[1] = Col_addr[2];
Col_addr[2] = Col_addr[3];
Col_addr[3] = {col_bits{1'b0}};
Bank_addr[0] = Bank_addr[1];
Bank_addr[1] = Bank_addr[2];
Bank_addr[2] = Bank_addr[3];
Bank_addr[3] = 2'b0;
Bank_precharge[0] = Bank_precharge[1];
Bank_precharge[1] = Bank_precharge[2];
Bank_precharge[2] = Bank_precharge[3];
Bank_precharge[3] = 2'b0;
A10_precharge[0] = A10_precharge[1];
A10_precharge[1] = A10_precharge[2];
A10_precharge[2] = A10_precharge[3];
A10_precharge[3] = 1'b0;
// Dqm pipeline for Read
Dqm_reg0 = Dqm_reg1;
Dqm_reg1 = Dqm;
// Read or Write with Auto Precharge Counter
if (Auto_precharge[0] == 1'b1) begin
Count_precharge[0] = Count_precharge[0] + 1;
end
if (Auto_precharge[1] == 1'b1) begin
Count_precharge[1] = Count_precharge[1] + 1;
end
if (Auto_precharge[2] == 1'b1) begin
Count_precharge[2] = Count_precharge[2] + 1;
end
if (Auto_precharge[3] == 1'b1) begin
Count_precharge[3] = Count_precharge[3] + 1;
end
// tMRD Counter
MRD_chk = MRD_chk + 1;
// tWR Counter for Write
WR_counter[0] = WR_counter[0] + 1;
WR_counter[1] = WR_counter[1] + 1;
WR_counter[2] = WR_counter[2] + 1;
WR_counter[3] = WR_counter[3] + 1;
// Auto Refresh
if (Aref_enable == 1'b1) begin
if (Debug) $display ("at time %t AREF : Auto Refresh", $time);
// Auto Refresh to Auto Refresh
if (($time - RC_chk < tRC)&&Debug) begin
$display ("at time %t ERROR: tRC violation during Auto Refresh", $time);
end
// Precharge to Auto Refresh
if (($time - RP_chk0 < tRP || $time - RP_chk1 < tRP || $time - RP_chk2 < tRP || $time - RP_chk3 < tRP)&&Debug) begin
$display ("at time %t ERROR: tRP violation during Auto Refresh", $time);
end
// Precharge to Refresh
if (Pc_b0 == 1'b0 || Pc_b1 == 1'b0 || Pc_b2 == 1'b0 || Pc_b3 == 1'b0) begin
$display ("at time %t ERROR: All banks must be Precharge before Auto Refresh", $time);
end
// Record Current tRC time
RC_chk = $time;
end
// Load Mode Register
if (Mode_reg_enable == 1'b1) begin
// Decode CAS Latency, Burst Length, Burst Type, and Write Burst Mode
if (Pc_b0 == 1'b1 && Pc_b1 == 1'b1 && Pc_b2 == 1'b1 && Pc_b3 == 1'b1) begin
Mode_reg = Addr;
if (Debug) begin
$display ("at time %t LMR : Load Mode Register", $time);
// CAS Latency
if (Addr[6 : 4] == 3'b010)
$display (" CAS Latency = 2");
else if (Addr[6 : 4] == 3'b011)
$display (" CAS Latency = 3");
else
$display (" CAS Latency = Reserved");
// Burst Length
if (Addr[2 : 0] == 3'b000)
$display (" Burst Length = 1");
else if (Addr[2 : 0] == 3'b001)
$display (" Burst Length = 2");
else if (Addr[2 : 0] == 3'b010)
$display (" Burst Length = 4");
else if (Addr[2 : 0] == 3'b011)
$display (" Burst Length = 8");
else if (Addr[3 : 0] == 4'b0111)
$display (" Burst Length = Full");
else
$display (" Burst Length = Reserved");
// Burst Type
if (Addr[3] == 1'b0)
$display (" Burst Type = Sequential");
else if (Addr[3] == 1'b1)
$display (" Burst Type = Interleaved");
else
$display (" Burst Type = Reserved");
// Write Burst Mode
if (Addr[9] == 1'b0)
$display (" Write Burst Mode = Programmed Burst Length");
else if (Addr[9] == 1'b1)
$display (" Write Burst Mode = Single Location Access");
else
$display (" Write Burst Mode = Reserved");
end
end else begin
$display ("at time %t ERROR: all banks must be Precharge before Load Mode Register", $time);
end
// REF to LMR
if ($time - RC_chk < tRC) begin
$display ("at time %t ERROR: tRC violation during Load Mode Register", $time);
end
// LMR to LMR
if (MRD_chk < tMRD) begin
$display ("at time %t ERROR: tMRD violation during Load Mode Register", $time);
end
MRD_chk = 0;
end
// Active Block (Latch Bank Address and Row Address)
if (Active_enable == 1'b1) begin
if (Ba == 2'b00 && Pc_b0 == 1'b1) begin
{Act_b0, Pc_b0} = 2'b10;
B0_row_addr = Addr [addr_bits - 1 : 0];
RCD_chk0 = $time;
RAS_chk0 = $time;
if (Debug) $display ("at time %t ACT : Bank = 0 Row = %d", $time, Addr);
// Precharge to Activate Bank 0
if ($time - RP_chk0 < tRP) begin
$display ("at time %t ERROR: tRP violation during Activate bank 0", $time);
end
end else if (Ba == 2'b01 && Pc_b1 == 1'b1) begin
{Act_b1, Pc_b1} = 2'b10;
B1_row_addr = Addr [addr_bits - 1 : 0];
RCD_chk1 = $time;
RAS_chk1 = $time;
if (Debug) $display ("at time %t ACT : Bank = 1 Row = %d", $time, Addr);
// Precharge to Activate Bank 1
if ($time - RP_chk1 < tRP) begin
$display ("at time %t ERROR: tRP violation during Activate bank 1", $time);
end
end else if (Ba == 2'b10 && Pc_b2 == 1'b1) begin
{Act_b2, Pc_b2} = 2'b10;
B2_row_addr = Addr [addr_bits - 1 : 0];
RCD_chk2 = $time;
RAS_chk2 = $time;
if (Debug) $display ("at time %t ACT : Bank = 2 Row = %d", $time, Addr);
// Precharge to Activate Bank 2
if ($time - RP_chk2 < tRP) begin
$display ("at time %t ERROR: tRP violation during Activate bank 2", $time);
end
end else if (Ba == 2'b11 && Pc_b3 == 1'b1) begin
{Act_b3, Pc_b3} = 2'b10;
B3_row_addr = Addr [addr_bits - 1 : 0];
RCD_chk3 = $time;
RAS_chk3 = $time;
if (Debug) $display ("at time %t ACT : Bank = 3 Row = %d", $time, Addr);
// Precharge to Activate Bank 3
if ($time - RP_chk3 < tRP) begin
$display ("at time %t ERROR: tRP violation during Activate bank 3", $time);
end
end else if (Ba == 2'b00 && Pc_b0 == 1'b0) begin
$display ("at time %t ERROR: Bank 0 is not Precharged.", $time);
end else if (Ba == 2'b01 && Pc_b1 == 1'b0) begin
$display ("at time %t ERROR: Bank 1 is not Precharged.", $time);
end else if (Ba == 2'b10 && Pc_b2 == 1'b0) begin
$display ("at time %t ERROR: Bank 2 is not Precharged.", $time);
end else if (Ba == 2'b11 && Pc_b3 == 1'b0) begin
$display ("at time %t ERROR: Bank 3 is not Precharged.", $time);
end
// Active Bank A to Active Bank B
if ((Previous_bank != Ba) && ($time - RRD_chk < tRRD)) begin
$display ("at time %t ERROR: tRRD violation during Activate bank = %d", $time, Ba);
end
// Load Mode Register to Active
if (MRD_chk < tMRD ) begin
$display ("at time %t ERROR: tMRD violation during Activate bank = %d", $time, Ba);
end
// Auto Refresh to Activate
if (($time - RC_chk < tRC)&&Debug) begin
$display ("at time %t ERROR: tRC violation during Activate bank = %d", $time, Ba);
end
// Record variables for checking violation
RRD_chk = $time;
Previous_bank = Ba;
end
// Precharge Block
if (Prech_enable == 1'b1) begin
if (Addr[10] == 1'b1) begin
{Pc_b0, Pc_b1, Pc_b2, Pc_b3} = 4'b1111;
{Act_b0, Act_b1, Act_b2, Act_b3} = 4'b0000;
RP_chk0 = $time;
RP_chk1 = $time;
RP_chk2 = $time;
RP_chk3 = $time;
if (Debug) $display ("at time %t PRE : Bank = ALL",$time);
// Activate to Precharge all banks
if (($time - RAS_chk0 < tRAS) || ($time - RAS_chk1 < tRAS) ||
($time - RAS_chk2 < tRAS) || ($time - RAS_chk3 < tRAS)) begin
$display ("at time %t ERROR: tRAS violation during Precharge all bank", $time);
end
// tWR violation check for write
if (($time - WR_chk[0] < tWRp) || ($time - WR_chk[1] < tWRp) ||
($time - WR_chk[2] < tWRp) || ($time - WR_chk[3] < tWRp)) begin
$display ("at time %t ERROR: tWR violation during Precharge all bank", $time);
end
end else if (Addr[10] == 1'b0) begin
if (Ba == 2'b00) begin
{Pc_b0, Act_b0} = 2'b10;
RP_chk0 = $time;
if (Debug) $display ("at time %t PRE : Bank = 0",$time);
// Activate to Precharge Bank 0
if ($time - RAS_chk0 < tRAS) begin
$display ("at time %t ERROR: tRAS violation during Precharge bank 0", $time);
end
end else if (Ba == 2'b01) begin
{Pc_b1, Act_b1} = 2'b10;
RP_chk1 = $time;
if (Debug) $display ("at time %t PRE : Bank = 1",$time);
// Activate to Precharge Bank 1
if ($time - RAS_chk1 < tRAS) begin
$display ("at time %t ERROR: tRAS violation during Precharge bank 1", $time);
end
end else if (Ba == 2'b10) begin
{Pc_b2, Act_b2} = 2'b10;
RP_chk2 = $time;
if (Debug) $display ("at time %t PRE : Bank = 2",$time);
// Activate to Precharge Bank 2
if ($time - RAS_chk2 < tRAS) begin
$display ("at time %t ERROR: tRAS violation during Precharge bank 2", $time);
end
end else if (Ba == 2'b11) begin
{Pc_b3, Act_b3} = 2'b10;
RP_chk3 = $time;
if (Debug) $display ("at time %t PRE : Bank = 3",$time);
// Activate to Precharge Bank 3
if ($time - RAS_chk3 < tRAS) begin
$display ("at time %t ERROR: tRAS violation during Precharge bank 3", $time);
end
end
// tWR violation check for write
if ($time - WR_chk[Ba] < tWRp) begin
$display ("at time %t ERROR: tWR violation during Precharge bank %d", $time, Ba);
end
end
// Terminate a Write Immediately (if same bank or all banks)
if (Data_in_enable == 1'b1 && (Bank == Ba || Addr[10] == 1'b1)) begin
Data_in_enable = 1'b0;
end
// Precharge Command Pipeline for Read
if (Cas_latency_3 == 1'b1) begin
Command[2] = `PRECH;
Bank_precharge[2] = Ba;
A10_precharge[2] = Addr[10];
end else if (Cas_latency_2 == 1'b1) begin
Command[1] = `PRECH;
Bank_precharge[1] = Ba;
A10_precharge[1] = Addr[10];
end
end
// Burst terminate
if (Burst_term == 1'b1) begin
// Terminate a Write Immediately
if (Data_in_enable == 1'b1) begin
Data_in_enable = 1'b0;
end
// Terminate a Read Depend on CAS Latency
if (Cas_latency_3 == 1'b1) begin
Command[2] = `BST;
end else if (Cas_latency_2 == 1'b1) begin
Command[1] = `BST;
end
if (Debug) $display ("at time %t BST : Burst Terminate",$time);
end
// Read, Write, Column Latch
if (Read_enable == 1'b1 || Write_enable == 1'b1) begin
// Check to see if bank is open (ACT)
if ((Ba == 2'b00 && Pc_b0 == 1'b1) || (Ba == 2'b01 && Pc_b1 == 1'b1) ||
(Ba == 2'b10 && Pc_b2 == 1'b1) || (Ba == 2'b11 && Pc_b3 == 1'b1)) begin
$display("at time %t ERROR: Cannot Read or Write - Bank %d is not Activated", $time, Ba);
end
// Activate to Read or Write
if ((Ba == 2'b00) && ($time - RCD_chk0 < tRCD))
$display("at time %t ERROR: tRCD violation during Read or Write to Bank 0", $time);
if ((Ba == 2'b01) && ($time - RCD_chk1 < tRCD))
$display("at time %t ERROR: tRCD violation during Read or Write to Bank 1", $time);
if ((Ba == 2'b10) && ($time - RCD_chk2 < tRCD))
$display("at time %t ERROR: tRCD violation during Read or Write to Bank 2", $time);
if ((Ba == 2'b11) && ($time - RCD_chk3 < tRCD))
$display("at time %t ERROR: tRCD violation during Read or Write to Bank 3", $time);
// Read Command
if (Read_enable == 1'b1) begin
// CAS Latency pipeline
if (Cas_latency_3 == 1'b1) begin
if (Addr[10] == 1'b1) begin
Command[2] = `READ_A;
end else begin
Command[2] = `READ;
end
Col_addr[2] = Addr;
Bank_addr[2] = Ba;
end else if (Cas_latency_2 == 1'b1) begin
if (Addr[10] == 1'b1) begin
Command[1] = `READ_A;
end else begin
Command[1] = `READ;
end
Col_addr[1] = Addr;
Bank_addr[1] = Ba;
end
// Read interrupt Write (terminate Write immediately)
if (Data_in_enable == 1'b1) begin
Data_in_enable = 1'b0;
end
// Write Command
end else if (Write_enable == 1'b1) begin
if (Addr[10] == 1'b1) begin
Command[0] = `WRITE_A;
end else begin
Command[0] = `WRITE;
end
Col_addr[0] = Addr;
Bank_addr[0] = Ba;
// Write interrupt Write (terminate Write immediately)
if (Data_in_enable == 1'b1) begin
Data_in_enable = 1'b0;
end
// Write interrupt Read (terminate Read immediately)
if (Data_out_enable == 1'b1) begin
Data_out_enable = 1'b0;
end
end
// Interrupting a Write with Autoprecharge
if (Auto_precharge[Bank] == 1'b1 && Write_precharge[Bank] == 1'b1) begin
RW_interrupt_write[Bank] = 1'b1;
if (Debug) $display ("at time %t NOTE : Read/Write Bank %d interrupt Write Bank %d with Autoprecharge", $time, Ba, Bank);
end
// Interrupting a Read with Autoprecharge
if (Auto_precharge[Bank] == 1'b1 && Read_precharge[Bank] == 1'b1) begin
RW_interrupt_read[Bank] = 1'b1;
if (Debug) $display ("at time %t NOTE : Read/Write Bank %d interrupt Read Bank %d with Autoprecharge", $time, Ba, Bank);
end
// Read or Write with Auto Precharge
if (Addr[10] == 1'b1) begin
Auto_precharge[Ba] = 1'b1;
Count_precharge[Ba] = 0;
if (Read_enable == 1'b1) begin
Read_precharge[Ba] = 1'b1;
end else if (Write_enable == 1'b1) begin
Write_precharge[Ba] = 1'b1;
end
end
end
// Read with Auto Precharge Calculation
// The device start internal precharge:
// 1. CAS Latency - 1 cycles before last burst
// and 2. Meet minimum tRAS requirement
// or 3. Interrupt by a Read or Write (with or without AutoPrecharge)
if ((Auto_precharge[0] == 1'b1) && (Read_precharge[0] == 1'b1)) begin
if ((($time - RAS_chk0 >= tRAS) && // Case 2
((Burst_length_1 == 1'b1 && Count_precharge[0] >= 1) || // Case 1
(Burst_length_2 == 1'b1 && Count_precharge[0] >= 2) ||
(Burst_length_4 == 1'b1 && Count_precharge[0] >= 4) ||
(Burst_length_8 == 1'b1 && Count_precharge[0] >= 8))) ||
(RW_interrupt_read[0] == 1'b1)) begin // Case 3
Pc_b0 = 1'b1;
Act_b0 = 1'b0;
RP_chk0 = $time;
Auto_precharge[0] = 1'b0;
Read_precharge[0] = 1'b0;
RW_interrupt_read[0] = 1'b0;
if (Debug) $display ("at time %t NOTE : Start Internal Auto Precharge for Bank 0", $time);
end
end
if ((Auto_precharge[1] == 1'b1) && (Read_precharge[1] == 1'b1)) begin
if ((($time - RAS_chk1 >= tRAS) &&
((Burst_length_1 == 1'b1 && Count_precharge[1] >= 1) ||
(Burst_length_2 == 1'b1 && Count_precharge[1] >= 2) ||
(Burst_length_4 == 1'b1 && Count_precharge[1] >= 4) ||
(Burst_length_8 == 1'b1 && Count_precharge[1] >= 8))) ||
(RW_interrupt_read[1] == 1'b1)) begin
Pc_b1 = 1'b1;
Act_b1 = 1'b0;
RP_chk1 = $time;
Auto_precharge[1] = 1'b0;
Read_precharge[1] = 1'b0;
RW_interrupt_read[1] = 1'b0;
if (Debug) $display ("at time %t NOTE : Start Internal Auto Precharge for Bank 1", $time);
end
end
if ((Auto_precharge[2] == 1'b1) && (Read_precharge[2] == 1'b1)) begin
if ((($time - RAS_chk2 >= tRAS) &&
((Burst_length_1 == 1'b1 && Count_precharge[2] >= 1) ||
(Burst_length_2 == 1'b1 && Count_precharge[2] >= 2) ||
(Burst_length_4 == 1'b1 && Count_precharge[2] >= 4) ||
(Burst_length_8 == 1'b1 && Count_precharge[2] >= 8))) ||
(RW_interrupt_read[2] == 1'b1)) begin
Pc_b2 = 1'b1;
Act_b2 = 1'b0;
RP_chk2 = $time;
Auto_precharge[2] = 1'b0;
Read_precharge[2] = 1'b0;
RW_interrupt_read[2] = 1'b0;
if (Debug) $display ("at time %t NOTE : Start Internal Auto Precharge for Bank 2", $time);
end
end
if ((Auto_precharge[3] == 1'b1) && (Read_precharge[3] == 1'b1)) begin
if ((($time - RAS_chk3 >= tRAS) &&
((Burst_length_1 == 1'b1 && Count_precharge[3] >= 1) ||
(Burst_length_2 == 1'b1 && Count_precharge[3] >= 2) ||
(Burst_length_4 == 1'b1 && Count_precharge[3] >= 4) ||
(Burst_length_8 == 1'b1 && Count_precharge[3] >= 8))) ||
(RW_interrupt_read[3] == 1'b1)) begin
Pc_b3 = 1'b1;
Act_b3 = 1'b0;
RP_chk3 = $time;
Auto_precharge[3] = 1'b0;
Read_precharge[3] = 1'b0;
RW_interrupt_read[3] = 1'b0;
if (Debug) $display ("at time %t NOTE : Start Internal Auto Precharge for Bank 3", $time);
end
end
// Internal Precharge or Bst
if (Command[0] == `PRECH) begin // Precharge terminate a read with same bank or all banks
if (Bank_precharge[0] == Bank || A10_precharge[0] == 1'b1) begin
if (Data_out_enable == 1'b1) begin
Data_out_enable = 1'b0;
end
end
end else if (Command[0] == `BST) begin // BST terminate a read to current bank
if (Data_out_enable == 1'b1) begin
Data_out_enable = 1'b0;
end
end
if (Data_out_enable == 1'b0) begin
Dq_reg <= #tOH {data_bits{1'bz}};
end
// Detect Read or Write command
if (Command[0] == `READ || Command[0] == `READ_A) begin
Bank = Bank_addr[0];
Col = Col_addr[0];
Col_brst = Col_addr[0];
if (Bank_addr[0] == 2'b00) begin
Row = B0_row_addr;
end else if (Bank_addr[0] == 2'b01) begin
Row = B1_row_addr;
end else if (Bank_addr[0] == 2'b10) begin
Row = B2_row_addr;
end else if (Bank_addr[0] == 2'b11) begin
Row = B3_row_addr;
end
Burst_counter = 0;
Data_in_enable = 1'b0;
Data_out_enable = 1'b1;
end else if (Command[0] == `WRITE || Command[0] == `WRITE_A) begin
Bank = Bank_addr[0];
Col = Col_addr[0];
Col_brst = Col_addr[0];
if (Bank_addr[0] == 2'b00) begin
Row = B0_row_addr;
end else if (Bank_addr[0] == 2'b01) begin
Row = B1_row_addr;
end else if (Bank_addr[0] == 2'b10) begin
Row = B2_row_addr;
end else if (Bank_addr[0] == 2'b11) begin
Row = B3_row_addr;
end
Burst_counter = 0;
Data_in_enable = 1'b1;
Data_out_enable = 1'b0;
end
// DQ buffer (Driver/Receiver)
if (Data_in_enable == 1'b1) begin // Writing Data to Memory
// Array buffer
if (Bank == 2'b00) Dq_dqm [data_bits - 1 : 0] = Bank0 [{Row, Col}];
if (Bank == 2'b01) Dq_dqm [data_bits - 1 : 0] = Bank1 [{Row, Col}];
if (Bank == 2'b10) Dq_dqm [data_bits - 1 : 0] = Bank2 [{Row, Col}];
if (Bank == 2'b11) Dq_dqm [data_bits - 1 : 0] = Bank3 [{Row, Col}];
// Dqm operation
if (Dqm[0] == 1'b0) Dq_dqm [ 7 : 0] = Dq [ 7 : 0];
if (Dqm[1] == 1'b0) Dq_dqm [15 : 8] = Dq [15 : 8];
//if (Dqm[2] == 1'b0) Dq_dqm [23 : 16] = Dq [23 : 16];
// if (Dqm[3] == 1'b0) Dq_dqm [31 : 24] = Dq [31 : 24];
// Write to memory
if (Bank == 2'b00) Bank0 [{Row, Col}] = Dq_dqm [data_bits - 1 : 0];
if (Bank == 2'b01) Bank1 [{Row, Col}] = Dq_dqm [data_bits - 1 : 0];
if (Bank == 2'b10) Bank2 [{Row, Col}] = Dq_dqm [data_bits - 1 : 0];
if (Bank == 2'b11) Bank3 [{Row, Col}] = Dq_dqm [data_bits - 1 : 0];
if (Bank == 2'b11 && Row==10'h3 && Col[7:4]==4'h4)
$display("at time %t WRITE: Bank = %d Row = %d, Col = %d, Data = Hi-Z due to DQM", $time, Bank, Row, Col);
//$fdisplay(test_file,"bank:%h row:%h col:%h write:%h",Bank,Row,Col,Dq_dqm);
// Output result
if (Dqm == 4'b1111) begin
if (Debug) $display("at time %t WRITE: Bank = %d Row = %d, Col = %d, Data = Hi-Z due to DQM", $time, Bank, Row, Col);
end else begin
if (Debug) $display("at time %t WRITE: Bank = %d Row = %d, Col = %d, Data = %d, Dqm = %b", $time, Bank, Row, Col, Dq_dqm, Dqm);
// Record tWR time and reset counter
WR_chk [Bank] = $time;
WR_counter [Bank] = 0;
end
// Advance burst counter subroutine
#tHZ Burst;
end else if (Data_out_enable == 1'b1) begin // Reading Data from Memory
//$display("%h , %h, %h",Bank0,Row,Col);
// Array buffer
if (Bank == 2'b00) Dq_dqm [data_bits - 1 : 0] = Bank0 [{Row, Col}];
if (Bank == 2'b01) Dq_dqm [data_bits - 1 : 0] = Bank1 [{Row, Col}];
if (Bank == 2'b10) Dq_dqm [data_bits - 1 : 0] = Bank2 [{Row, Col}];
if (Bank == 2'b11) Dq_dqm [data_bits - 1 : 0] = Bank3 [{Row, Col}];
// Dqm operation
if (Dqm_reg0[0] == 1'b1) Dq_dqm [ 7 : 0] = 8'bz;
if (Dqm_reg0[1] == 1'b1) Dq_dqm [15 : 8] = 8'bz;
if (Dqm_reg0[2] == 1'b1) Dq_dqm [23 : 16] = 8'bz;
if (Dqm_reg0[3] == 1'b1) Dq_dqm [31 : 24] = 8'bz;
// Display result
Dq_reg [data_bits - 1 : 0] = #tAC Dq_dqm [data_bits - 1 : 0];
if (Dqm_reg0 == 4'b1111) begin
if (Debug) $display("at time %t READ : Bank = %d Row = %d, Col = %d, Data = Hi-Z due to DQM", $time, Bank, Row, Col);
end else begin
if (Debug) $display("at time %t READ : Bank = %d Row = %d, Col = %d, Data = %d, Dqm = %b", $time, Bank, Row, Col, Dq_reg, Dqm_reg0);
end
// Advance burst counter subroutine
Burst;
end
end
// Write with Auto Precharge Calculation
// The device start internal precharge:
// 1. tWR Clock after last burst
// and 2. Meet minimum tRAS requirement
// or 3. Interrupt by a Read or Write (with or without AutoPrecharge)
always @ (WR_counter[0]) begin
if ((Auto_precharge[0] == 1'b1) && (Write_precharge[0] == 1'b1)) begin
if ((($time - RAS_chk0 >= tRAS) && // Case 2
(((Burst_length_1 == 1'b1 || Write_burst_mode == 1'b1) && Count_precharge [0] >= 1) || // Case 1
(Burst_length_2 == 1'b1 && Count_precharge [0] >= 2) ||
(Burst_length_4 == 1'b1 && Count_precharge [0] >= 4) ||
(Burst_length_8 == 1'b1 && Count_precharge [0] >= 8))) ||
(RW_interrupt_write[0] == 1'b1 && WR_counter[0] >= 2)) begin // Case 3 (stop count when interrupt)
Auto_precharge[0] = 1'b0;
Write_precharge[0] = 1'b0;
RW_interrupt_write[0] = 1'b0;
#tWRa; // Wait for tWR
Pc_b0 = 1'b1;
Act_b0 = 1'b0;
RP_chk0 = $time;
if (Debug) $display ("at time %t NOTE : Start Internal Auto Precharge for Bank 0", $time);
end
end
end
always @ (WR_counter[1]) begin
if ((Auto_precharge[1] == 1'b1) && (Write_precharge[1] == 1'b1)) begin
if ((($time - RAS_chk1 >= tRAS) &&
(((Burst_length_1 == 1'b1 || Write_burst_mode == 1'b1) && Count_precharge [1] >= 1) ||
(Burst_length_2 == 1'b1 && Count_precharge [1] >= 2) ||
(Burst_length_4 == 1'b1 && Count_precharge [1] >= 4) ||
(Burst_length_8 == 1'b1 && Count_precharge [1] >= 8))) ||
(RW_interrupt_write[1] == 1'b1 && WR_counter[1] >= 2)) begin
Auto_precharge[1] = 1'b0;
Write_precharge[1] = 1'b0;
RW_interrupt_write[1] = 1'b0;
#tWRa; // Wait for tWR
Pc_b1 = 1'b1;
Act_b1 = 1'b0;
RP_chk1 = $time;
if (Debug) $display ("at time %t NOTE : Start Internal Auto Precharge for Bank 1", $time);
end
end
end
always @ (WR_counter[2]) begin
if ((Auto_precharge[2] == 1'b1) && (Write_precharge[2] == 1'b1)) begin
if ((($time - RAS_chk2 >= tRAS) &&
(((Burst_length_1 == 1'b1 || Write_burst_mode == 1'b1) && Count_precharge [2] >= 1) ||
(Burst_length_2 == 1'b1 && Count_precharge [2] >= 2) ||
(Burst_length_4 == 1'b1 && Count_precharge [2] >= 4) ||
(Burst_length_8 == 1'b1 && Count_precharge [2] >= 8))) ||
(RW_interrupt_write[2] == 1'b1 && WR_counter[2] >= 2)) begin
Auto_precharge[2] = 1'b0;
Write_precharge[2] = 1'b0;
RW_interrupt_write[2] = 1'b0;
#tWRa; // Wait for tWR
Pc_b2 = 1'b1;
Act_b2 = 1'b0;
RP_chk2 = $time;
if (Debug) $display ("at time %t NOTE : Start Internal Auto Precharge for Bank 2", $time);
end
end
end
always @ (WR_counter[3]) begin
if ((Auto_precharge[3] == 1'b1) && (Write_precharge[3] == 1'b1)) begin
if ((($time - RAS_chk3 >= tRAS) &&
(((Burst_length_1 == 1'b1 || Write_burst_mode == 1'b1) && Count_precharge [3] >= 1) ||
(Burst_length_2 == 1'b1 && Count_precharge [3] >= 2) ||
(Burst_length_4 == 1'b1 && Count_precharge [3] >= 4) ||
(Burst_length_8 == 1'b1 && Count_precharge [3] >= 8))) ||
(RW_interrupt_write[3] == 1'b1 && WR_counter[3] >= 2)) begin
Auto_precharge[3] = 1'b0;
Write_precharge[3] = 1'b0;
RW_interrupt_write[3] = 1'b0;
#tWRa; // Wait for tWR
Pc_b3 = 1'b1;
Act_b3 = 1'b0;
RP_chk3 = $time;
if (Debug) $display ("at time %t NOTE : Start Internal Auto Precharge for Bank 3", $time);
end
end
end
task Burst;
begin
// Advance Burst Counter
Burst_counter = Burst_counter + 1;
// Burst Type
if (Mode_reg[3] == 1'b0) begin // Sequential Burst
Col_temp = Col + 1;
end else if (Mode_reg[3] == 1'b1) begin // Interleaved Burst
Col_temp[2] = Burst_counter[2] ^ Col_brst[2];
Col_temp[1] = Burst_counter[1] ^ Col_brst[1];
Col_temp[0] = Burst_counter[0] ^ Col_brst[0];
end
// Burst Length
if (Burst_length_2) begin // Burst Length = 2
Col [0] = Col_temp [0];
end else if (Burst_length_4) begin // Burst Length = 4
Col [1 : 0] = Col_temp [1 : 0];
end else if (Burst_length_8) begin // Burst Length = 8
Col [2 : 0] = Col_temp [2 : 0];
end else begin // Burst Length = FULL
Col = Col_temp;
end
// Burst Read Single Write
if (Write_burst_mode == 1'b1) begin
Data_in_enable = 1'b0;
end
// Data Counter
if (Burst_length_1 == 1'b1) begin
if (Burst_counter >= 1) begin
Data_in_enable = 1'b0;
Data_out_enable = 1'b0;
end
end else if (Burst_length_2 == 1'b1) begin
if (Burst_counter >= 2) begin
Data_in_enable = 1'b0;
Data_out_enable = 1'b0;
end
end else if (Burst_length_4 == 1'b1) begin
if (Burst_counter >= 4) begin
Data_in_enable = 1'b0;
Data_out_enable = 1'b0;
end
end else if (Burst_length_8 == 1'b1) begin
if (Burst_counter >= 8) begin
Data_in_enable = 1'b0;
Data_out_enable = 1'b0;
end
end
end
endtask
//**********************将SDRAM内的数据直接输出到外部文件*******************************//
/*
integer sdram_data,ind;
always@(sdram_r)
begin
sdram_data=$fopen("sdram_data.txt");
$display("Sdram dampout begin ",sdram_data);
// $fdisplay(sdram_data,"Bank0：");
for(ind=0;ind<=mem_sizes;ind=ind+1)
$fdisplay(sdram_data,"%h %b",ind,Bank0[ind]);
// $fdisplay(sdram_data,"Bank1：");
for(ind=0;ind<=mem_sizes;ind=ind+1)
$fdisplay(sdram_data,"%h %b",ind,Bank1[ind]);
// $fdisplay(sdram_data,"Bank2：");
for(ind=0;ind<=mem_sizes;ind=ind+1)
$fdisplay(sdram_data,"%h %b",ind,Bank2[ind]);
// $fdisplay(sdram_data,"Bank3：");
for(ind=0;ind<=mem_sizes;ind=ind+1)
$fdisplay(sdram_data,"%h %b",ind,Bank3[ind]);
$fclose("sdram_data.txt");
//->compare;
end
*/
integer sdram_data,sdram_mem;
reg [23:0] aa,cc;
reg [18:0] bb,ee;
always@(sdram_r)
begin
$display("Sdram dampout begin ",$realtime);
sdram_data=$fopen("sdram_data.txt");
for(aa=0;aa<4*(mem_sizes+1);aa=aa+1)
begin
bb=aa[18:0];
if(aa<=mem_sizes)
$fdisplay(sdram_data,"%0d %0h",aa,Bank0[bb]);
else if(aa<=2*mem_sizes+1)
$fdisplay(sdram_data,"%0d %0h",aa,Bank1[bb]);
else if(aa<=3*mem_sizes+2)
$fdisplay(sdram_data,"%0d %0h",aa,Bank2[bb]);
else
$fdisplay(sdram_data,"%0d %0h",aa,Bank3[bb]);
end
$fclose("sdram_data.txt");
sdram_mem=$fopen("sdram_mem.txt");
for(cc=0;cc<4*(mem_sizes+1);cc=cc+1)
begin
ee=cc[18:0];
if(cc<=mem_sizes)
$fdisplay(sdram_mem,"%0h",Bank0[ee]);
else if(cc<=2*mem_sizes+1)
$fdisplay(sdram_mem,"%0h",Bank1[ee]);
else if(cc<=3*mem_sizes+2)
$fdisplay(sdram_mem,"%0h",Bank2[ee]);
else
$fdisplay(sdram_mem,"%0h",Bank3[ee]);
end
$fclose("sdram_mem.txt");
end
// // Timing Parameters for -75 (PC133) and CAS Latency = 2
// specify
// specparam
tAH = 0.8, // Addr, Ba Hold Time
tAS = 1.5, // Addr, Ba Setup Time
tCH = 2.5, // Clock High-Level Width
tCL = 2.5, // Clock Low-Level Width
// tCK = 10.0, // Clock Cycle Time 100mhz
// tCK = 7.5, // Clock Cycle Time 133mhz
tCK = 7, // Clock Cycle Time 143mhz
tDH = 0.8, // Data-in Hold Time
tDS = 1.5, // Data-in Setup Time
tCKH = 0.8, // CKE Hold Time
tCKS = 1.5, // CKE Setup Time
tCMH = 0.8, // CS#, RAS#, CAS#, WE#, DQM# Hold Time
tCMS = 1.5; // CS#, RAS#, CAS#, WE#, DQM# Setup Time
// tAH = 1, // Addr, Ba Hold Time
// tAS = 1.5, // Addr, Ba Setup Time
// tCH = 1, // Clock High-Level Width
// tCL = 3, // Clock Low-Level Width
tCK = 10.0, // Clock Cycle Time 100mhz
tCK = 7.5, // Clock Cycle Time 133mhz
// tCK = 7, // Clock Cycle Time 143mhz
// tDH = 1, // Data-in Hold Time
// tDS = 2, // Data-in Setup Time
// tCKH = 1, // CKE Hold Time
// tCKS = 2, // CKE Setup Time
// tCMH = 0.8, // CS#, RAS#, CAS#, WE#, DQM# Hold Time
// tCMS = 1.5; // CS#, RAS#, CAS#, WE#, DQM# Setup Time
// $width (posedge Clk, tCH);
// $width (negedge Clk, tCL);
// $period (negedge Clk, tCK);
// $period (posedge Clk, tCK);
// $setuphold(posedge Clk, Cke, tCKS, tCKH);
// $setuphold(posedge Clk, Cs_n, tCMS, tCMH);
// $setuphold(posedge Clk, Cas_n, tCMS, tCMH);
// $setuphold(posedge Clk, Ras_n, tCMS, tCMH);
// $setuphold(posedge Clk, We_n, tCMS, tCMH);
// $setuphold(posedge Clk, Addr, tAS, tAH);
// $setuphold(posedge Clk, Ba, tAS, tAH);
// $setuphold(posedge Clk, Dqm, tCMS, tCMH);
// $setuphold(posedge Dq_chk, Dq, tDS, tDH);
// endspecify
endmodule
具体PLL核的文件就没必要给了，如果不会配置PLL IP核可以看我往期的文章，我们进入modelsim进行仿真：
Modelsim仿真：
可以看到，信息栏打印结果告诉我们执行了一次预充电，和八次自刷新以及配置的寄存器参数，模块功能完美实现，并且我们可以查看波形图数据：
发现符合预期，模块前仿真阶段设计成功！
本次单篇内容有些过长了，因此其它部分放在下节详解，通过手把手的分析，我们可以发现，其实数字系统设计并不会很难，我们只要把大的系统分解成小的，然后再把小的使用状态机进行描述，再一步步往上组装，最终可以完成整个系统的设计。