被动接口的配置

被动接口的配置
<router 0 f 0/0 口上做被动接口 >
 
Router 0 的配置:
Router>en
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int f0/0
Router(config-if)#ip add 10.1.1.1 255.0.0.0
Router(config-if)#no shutdown
 
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int f0/1
Router(config-if)#ip add 11.1.1.1 255.0.0.0
Router(config-if)#no shut
 
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
Router(config-if)#end
%SYS-5-CONFIG_I: Configured from console by console
Router(config)#router rip
Router(config-router)#passive-interface f
Router(config-router)#passive-interface fastEthernet 0/0
Router(config-router)#end
%SYS-5-CONFIG_I: Configured from console by console
 
Router#show ip rou
Router#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF , IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default, U - per-user static route, o - ODR
       P - periodic downloaded static route
 
Gateway of last resort is not set
 
C    10.0.0.0/8 is directly connected, FastEthernet0/0
C    11.0.0.0/8 is directly connected, FastEthernet0/1
Router#ping 10.1.1.3
 
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 6/8/9 ms
 
Router#
 
 
 
Router 1 的配置 :
Router>en
Router#conf
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int f0/0
Router(config-if)#ip add 10.1.1.2 255.0.0.0
Router(config-if)#no shut
 
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#router rip
Router(config-router)#ne
Router(config-router)#network 10.0.0.0
Router(config-router)#end
%SYS-5-CONFIG_I: Configured from console by console
Router#show ip rou
Router#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF , IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default, U - per-user static route, o - ODR
       P - periodic downloaded static route
 
Gateway of last resort is not set
 
C    10.0.0.0/8 is directly connected, FastEthernet0/0
Router#ping 10.1.1.3
 
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 8/9/11 ms
 
Router#ping 11.1.1.2
 
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 11.1.1.2, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
 
Router#
 
 
Router 2 的配置:
Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int f0/0
Router(config-if)#ip add 10.1.1.3 255.0.0.0
Router(config-if)#no shut
 
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#router  r
Router(config-router)#net 10.0.0.0
Router(config-router)#end
%SYS-5-CONFIG_I: Configured from console by console
Router#show ip rou
Router#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF , IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default, U - per-user static route, o - ODR
       P - periodic downloaded static route
 
Gateway of last resort is not set
 
C    10.0.0.0/8 is directly connected, FastEthernet0/0
Router#ping 10.1.1.2
 
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.1.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 7/8/10 ms
 
Router#ping 11.1.1.2
 
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 11.1.1.2, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
 
Router#
 

你可能感兴趣的:(职场,休闲,被动接口)