H3C基础命令

交换机命令
[Quidway]super password                                     ；修改特权用户密码
[Quidway]sysname                                     ；交换机命名
[Quidway]interface ethernet 0/1                            ；进入接口视图
[Quidway]interface vlan x                            ；进入接口视图
[Quidway-Vlan-interfacex]ip address 10.65.1.1 255.255.0.0     ；配置VLAN的IP地址
[Quidway]ip route-static 0.0.0.0 0.0.0.0 10.65.1.2          ；静态路由＝网关

[Quidway]user-interface vty 0 4                            ；进入虚拟终端
[S3026-ui-vty0-4]authentication-mode password                 ；设置口令模式
[S3026-ui-vty0-4]set authentication-mode password simple 222   ；设置口令
[S3026-ui-vty0-4]user privilege level 3                       ；用户级别

[Quidway-Ethernet0/1]duplex {half|full|auto}                ；配置端口工作状态
[Quidway-Ethernet0/1]speed {10|100|auto}                ；配置端口工作速率
[Quidway-Ethernet0/1]flow-control                      ；配置端口流控
[Quidway-Ethernet0/1]mdi {across|auto|normal}                 ；配置端口平接扭接
[Quidway-Ethernet0/1]port link-type {trunk|access|hybrid}     ；设置端口工作模式
[Quidway-Ethernet0/1]undo shutdown                       ；激活端口
[Quidway-Ethernet0/2]quit                            ；退出系统视图

[Quidway]vlan 3                                   　　　　　　；创建VLAN
[Quidway-vlan3]port ethernet 0/1 to ethernet 0/4 　　　　　；在VLAN中增加端口
[Quidway-Ethernet0/2]port access vlan 3          　　　　　；当前端口加入到VLAN
[Quidway-Ethernet0/2]port trunk permit vlan {ID|All}    　　；设trunk允许的VLAN
[Quidway-Ethernet0/2]port trunk pvid vlan 3     　　　　　；设置trunk端口的PVID

[Quidway]monitor-port <interface_type interface_num>        　；指定镜像端口
[Quidway]port mirror <interface_type interface_num>    　　；指定被镜像端口
[Quidway]port mirror int_list observing-port int_type int_num ；指定镜像和被镜像

[Quidway]description string                      　　　　　；指定VLAN描述字符
[Quidway]description                         　　　　　　 　；删除VLAN描述字符
[Quidway]display vlan [vlan_id]                            ；查看VLAN设置

[Quidway]stp {enable|disable}                               ；设置生成树,默认关闭
[Quidway]stp priority 4096                          　　　　　；设置交换机的优先级
[Quidway]stp root {primary|secondary}             　　　　　；设置为根或根的备份
[Quidway-Ethernet0/1]stp cost 200                　　　　　；设置交换机端口的花费

[SwitchA-vlanx]isolate-user-vlan enable          　　　　　；设置主vlan
[SwitchA]Isolate-user-vlan <x> secondary <list>     　　　　　；设置主vlan包括的子vlan
[Quidway-Ethernet0/2]port hybrid pvid vlan <id>     　　　　　；设置vlan的pvid
[Quidway-Ethernet0/2]port hybrid pvid             　　　　　；删除vlan的pvid
[Quidway-Ethernet0/2]port hybrid vlan vlan_id_list untagged 　；设置无标识的vlan
如果包的vlan id与PVId一致，则去掉vlan信息. 默认PVID=1。
所以设置PVID为所属vlan id, 设置可以互通的vlan为untagged.
－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－－
路由器命令

[Quidway]display version                          　　　　　　；显示版本信息
[Quidway]display current-configuration          　　　　　　；显示当前配置
[Quidway]display interfaces                       　　　　　　；显示接口信息
[Quidway]display ip route                      　　　　　　；显示路由信息

[Quidway]sysname aabbcc                         　　　　　　；更改主机名
[Quidway]super passwrod 123456                    　　　　　　；设置口令
[Quidway]interface serial0                      　　　　　　；进入接口
[Quidway-serial0]ip address <ip> <mask|mask_len>   　　　　　　；配置端口IP地址
[Quidway-serial0]undo shutdown                    　　　　　　；激活端口
[Quidway]link-protocol hdlc                       　　　　　　；绑定hdlc协议
[Quidway]user-interface vty 0 4
[Quidway-ui-vty0-4]authentication-mode password
[Quidway-ui-vty0-4]set authentication-mode password simple 222
[Quidway-ui-vty0-4]user privilege level 3
[Quidway-ui-vty0-4]quit

[Quidway]debugging hdlc all serial0             　　　　　　；显示所有信息
[Quidway]debugging hdlc event serial0          　　　　　　；调试事件信息
[Quidway]debugging hdlc packet serial0          　　　　　　；显示包的信息

静态路由：
[Quidway]ip route-static <ip><mask>{interface number|nexthop}[value][reject|blackhole]
例如：
[Quidway]ip route-static 129.1.0.0 16 10.0.0.2
[Quidway]ip route-static 129.1.0.0 255.255.0.0 10.0.0.2
[Quidway]ip route-static 129.1.0.0 16 Serial 2
[Quidway]ip route-static 0.0.0.0 0.0.0.0   10.0.0.2

动态路由：
[Quidway]rip                                                  ；设置动态路由
[Quidway]rip work                                           ；设置工作允许
[Quidway]rip input                                            ；设置入口允许
[Quidway]rip output                                        ；设置出口允许
[Quidway-rip]network 1.0.0.0                       　　　　　 ；设置交换路由网络
[Quidway-rip]network all                                      ；设置与所有网络交换
[Quidway-rip]peer ip-address                               ；
[Quidway-rip]summary                                        ；路由聚合
[Quidway]rip version 1                                     ；设置工作在版本1
[Quidway]rip version 2 multicast                            ；设置工作在版本2，多播方式
[Quidway-Ethernet0]rip split-horizon                          ；水平分隔

[Quidway]router id A.B.C.D                                  ；配置路由器的ID
[Quidway]ospf enable                                        ；启动OSPF协议
[Quidway-ospf]import-route direct                             ；引入直联路由
[Quidway-Serial0]ospf enable area <area_id>                ；配置OSPF区域

标准访问列表命令格式如下：
acl <acl-number> [match-order config|auto]                    ；默认前者顺序匹配。
rule [normal|special]{permit|deny} [source source-addr source-wildcard|any]
例：
[Quidway]acl 10
[Quidway-acl-10]rule normal permit source 10.0.0.0 0.0.0.255
[Quidway-acl-10]rule normal deny source any

扩展访问控制列表配置命令
配置TCP/UDP协议的扩展访问列表：
rule {normal|special}{permit|deny}{tcp|udp}source {<ip wild>|any}destination <ip wild>|any}
[operate]

配置ICMP协议的扩展访问列表：
rule {normal|special}{permit|deny}icmp source {<ip wild>|any]destination {<ip wild>|any]
[icmp-code] [logging]

扩展访问控制列表操作符的含义
equal portnumber                                     ；等于
greater-than portnumber                                     ；大于
less-than portnumber                                     ；小于
not-equal portnumber                                     ；不等
range portnumber1 portnumber2                               ；区间

扩展访问控制列表举例
[Quidway]acl 101
[Quidway-acl-101]rule deny souce any destination any
[Quidway-acl-101]rule permit icmp source any destination any icmp-type echo
[Quidway-acl-101]rule permit icmp source any destination any icmp-type echo-reply

[Quidway]acl 102
[Quidway-acl-102]rule permit ip source 10.0.0.1 0.0.0.0 destination 202.0.0.1 0.0.0.0
[Quidway-acl-102]rule deny ip source any destination any

[Quidway]acl 103
[Quidway-acl-103]rule permit tcp source any destination 10.0.0.1 0.0.0.0 destination-port

equal ftp
[Quidway-acl-103]rule permit tcp source any destination 10.0.0.2 0.0.0.0 destination-port

equal www

 

[Quidway]firewall enable
[Quidway]firewall default permit|deny
[Quidway]int e0
[Quidway-Ethernet0]firewall packet-filter 101 inbound|outbound

 

地址转换配置举例
[Quidway]firewall enable
[Quidway]firewall default permit
[Quidway]acl 101
[Quidway-acl-101]rule deny ip source any destination any
[Quidway-acl-101]rule permit ip source 129.38.1.4 0 destination any
[Quidway-acl-101]rule permit ip source 129.38.1.1 0 destination any
[Quidway-acl-101]rule permit ip source 129.38.1.2 0 destination any
[Quidway-acl-101]rule permit ip source 129.38.1.3 0 destination any
[Quidway]acl 102
[Quidway-acl-102]rule permit tcp source 202.39.2.3 0 destination 202.38.160.1 0
[Quidway-acl-102]rule permit tcp source any destination 202.38.160.1 0 destination-port

great-than
1024

[Quidway-Ethernet0]firewall packet-filter 101 inbound
[Quidway-Serial0]firewall packet-filter 102 inbound

[Quidway]nat address-group 202.38.160.101 202.38.160.103 pool1
[Quidway]acl 1
[Quidway-acl-1]rule permit source 10.110.10.0 0.0.0.255
[Quidway-acl-1]rule deny source any
[Quidway-acl-1]int serial 0
[Quidway-Serial0]nat outbound 1 address-group pool1

[Quidway-Serial0]nat server global 202.38.160.101 inside 10.110.10.1 ftp tcp
[Quidway-Serial0]nat server global 202.38.160.102 inside 10.110.10.2 www tcp
[Quidway-Serial0]nat server global 202.38.160.102 8080 inside 10.110.10.3 www tcp
[Quidway-Serial0]nat server global 202.38.160.103 inside 10.110.10.4 smtp udp

 

PPP验证：
主验方：pap|chap
[Quidway]local-user u2 password {simple|cipher} aaa
[Quidway]interface serial 0
[Quidway-serial0]ppp authentication-mode {pap|chap}
[Quidway-serial0]ppp chap user u1        //pap时，不用此句

pap被验方：
[Quidway]interface serial 0
[Quidway-serial0]ppp pap local-user u2 password {simple|cipher} aaa

chap被验方：
[Quidway]interface serial 0
[Quidway-serial0]ppp chap user u1
[Quidway-serial0]local-user u2 password {simple|cipher} aaa