IPV6静态路由与RIPng的配置
IPV6静态路由与RIPng的配置
实验拓扑:
R1(s2/1)-(s2/1)R2(s2/2)-(s2/1)R3
一:静态路由配置:
R1#
ipv6 unicast-routing//启用IPv6的单播路由,默认关闭
interface Serial2/1
ipv6 address 12::1/64
ipv6 route 23::/64 Serial2/1//配置一条到23网段的静态路由
R2#
ipv6 unicast-routing
interface Serial2/1
ipv6 address 12::2/64
interface Serial2/2
ipv6 address 23::2/64
R3#
ipv6 unicast-routing
interface Serial2/1
ipv6 address 23::3/64
ipv6 route 12::/64 Serial2/1
R1#show ipv route
IPv6 Routing Table - 5 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
C12::/64 [0/0]
via ::, Serial2/1
L12::1/128 [0/0]
via ::, Serial2/1
S23::/64 [1/0]//收到了R3上的静态路由
via ::, Serial2/1
LFE80::/10 [0/0]
via ::, Null0
LFF00::/8 [0/0]
via ::, Null0
R2#show ipv route
IPv6 Routing Table - 6 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
C12::/64 [0/0]
via ::, Serial2/1
L12::2/128 [0/0]
via ::, Serial2/1
C23::/64 [0/0]
via ::, Serial2/2
L23::2/128 [0/0]
via ::, Serial2/2
LFE80::/10 [0/0]
via ::, Null0
LFF00::/8 [0/0]
via ::, Null0
R3#show ipv route
IPv6 Routing Table - 5 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
U - Per-user Static route
I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
S12::/64 [1/0]//收到了R1上的静态路由
via ::, Serial2/1
C23::/64 [0/0]
via ::, Serial2/1
L23::3/128 [0/0]
via ::, Serial2/1
LFE80::/10 [0/0]
via ::, Null0
LFF00::/8 [0/0]
via ::, Null0
R1#ping ipv6 23::3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 23::3, timeout is 2 seconds:
!!!!!//通了
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/76/112 ms
RIPng配置
实验配置:
R1#
ipv6 unicast-routing//启用IPV6的单播路由功能
interface Serial2/1
ipv6 address 12::1/64//在接口下配置IPV6地址
ipv6 rip A1 enable//在接口下启用RIPng,跟IPV4下配置RIP的区别
R2#
ipv6 unicast-routing
interface Serial2/1
ipv6 address 12::2/64
ipv6 rip A1 enable
interface Serial2/2
ipv6 address 23::2/64
ipv6 rip A1 enable
R3#
ipv6 unicast-routing
interface Serial2/1
ipv6 address 23::3/64
ipv6 rip A1 enable
R1#ping ipv6 23::3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 23::3, timeout is 2 seconds:
!!!!!//通了
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/76/112 ms