Cisco IOS Naming ― Cisco IOS 命名规则

Cisco IOS Naming ― Cisco IOS 命名规则(1)
2008年01月06日 星期日 13:39
 
Last Updated: June 13, 2005
This reference is intended to assist engineers in ascertaining the feature sets included with an image. In most cases, the image name should correspond with the image name as downloaded from CCO. Assuming this to be the case, the image will have many numbers and letters in it, which indicate the feature functionality included in the image. The list below, while not "comprehensive," is a list of the most popular codes in a IOS naming convention.
"Legacy naming" - Letters at the beginning
IOS Code Letter
Feature
a
APPN
a2
ATM
a3
SNASW
b
Appletalk Routing
c
Remote Access Server
d
Desktop routing
dsc
Dial Shelf Controller
g5
Enterprise Wireless (7200)
g6
GPRS Gateway Support Node (7200)
i
IP routing
i5
IP routing, no ISDN (mc3810)
in
Base IP (8500CSR)
j
Enterprise (kitchen sink routing)
n
IPX Routing (low-end routers)
p
Service Provider (or DOCSIS for uBR)
r(x)
IBM
telco
Telco
w3
Distributed Director
wp
IP/ATM Base Image (8500MSR,LS1010)
y/y5
IP Routing (low-end routers)
(missing some IP routing/features like BGP)
y7
IP/ADSL
--文章超过最大长度,未完待续
 
"Legacy Naming" - Letters in the middle
56i
Encryption(DES)
ent
Plus (only when used with 'telco')
k1
BPI
k2/k8/k9
Encryption(DES=k8, 3DES=k9)
o
Firewall
o3
Firewall/IDS
s
Plus , or "LAN Only" on Cat6K/7600
s2
Voice IP to IP Voice Gateway (26xx/36xx/37xx only)
s3
"Basic" (limited IP routing, for limited-memory 26xx, 36xx)
s4
"Basic" without switching
s5
"Basic" without HD analog/AIM/Voice
t
Telco Return
v
VIP Support
v3,v8
Voice (17xx) - v3=VOICE, v8=VOX
w6
Wireless
x(or x2)
MCM
"Legacy Naming" - Letters at the end
l
Runs from Flash
m
Runs from RAM
z
Compressed image
Notes - "Legacy Naming" Conventions
7200 and 7500 images for "IP Only" are always "IP Plus." Therefore, Base IP supports IP Gateway cards like the PA-VXC's, whereas in the 17/26/36/37xx's you need IP Plus.
In the 1700, the "s" for PLUS feature sets sometimes is the first letter, as opposed in the middle, and the "y" for IP is sometimes at the end, instead of the beginning.
Some sample decodes:
c1700-bk2no3r2sv3y7-mz.121-5.YB5.bin - 12.1(5)YB2, AT/3DES/IPX/FW/IDS/IBM/Plus/Voice/IP/ADSL, runs from RAM and is a compressed image
c7200-is-mz.121-11.bin - 12.1(11) mainline, IP Only (note: this is a 7200, so IP Plus = IP), runs from RAM and is a compressed image
"Legacy Naming" - Feature Sets - Common Features Needed
Plus - Needed for modems, ATM, voice (non-17xx), DLSw+. Also adds "back in" IP features not in low-end router "y" images, like BGP.
VIP Support - Needed for VIP2/4/6 (75xx), FlexWAN (C6K)
Desktop - Has IP, IPX, and usually AT. Some older IOS revs have DEC/LAT in there, too.
Enterprise - "Kitchen Sink" - has every protocol possible, except those that require their own letter code.
--文章超过最大长度,未完待续
New IOS Naming - Eight Feature Sets
In early 2003, the IOS teams in Cisco redid the IOS feature sets to "pull in the reigns," so to speak, and get the whole granular list "boiled down" to just a few feature sets. This will (hopefully) make choosing a feature set easier as time moves on. Certain IOS feature sets that are "specials" - for instance,
H.323/MCM, will always be separate.
These sets were introduced first on the 1700, 2600XM, 2691, and 3700 series routers in 12.3 mainline. 12.3T will have only the new feature sets for these platforms and new ones. Later on, 12.2S and 12.3 special releases for the 7200, 10000, 12000, and other routers are planned to follow the same example.
The key concept is "inheritance" - when you "move up" the diagram above, you "inherit" all the features from the feature sets below. For instance, Advanced IP Services combines the features in Advanced Security, Service Provider Services, IP Voice, and IP Base. Feature sets are easier to see their names, as well (substitute "2600" or "3700" or any other router model in place of "xxxx"):
Image Name
Feature Set
cxxxx-ipbase-mz
IP Base
cxxxx-ipvoice-mz
IP Voice
cxxxx-advsecurityk9-mz
Advanced Security (note k9=strong encryption)
cxxxx-spservicesk9-mz
Service Provider Services (note: also known as SP Services)
cxxxx-entbase-mz
Enterprise Base
cxxxx-advipservicesk9-mz
Advanced IP Services
cxxxx-entservicesk9-mz
Enterprise Services
cxxxx-adventerprisek9-mz
Advanced Enterprise Services
 
Notes - New IOS Naming
With the transition to new feature sets, no doubt many end users will want to know what feature is in which feature set. For any installation, it is always recommended to first use the lookup tool known as Feature Navigator, located at http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp
However, in a quick reference, please consult the following to figure out which feature set you need:
IP Base - Entry-level image, rolls up into all other images. Provides core routing functionality, including static routes, RIP, OSPF, EIGRP, for IPv4 only. Includes modems (both analog and digital) trunking (802.1q and ISL) and DSL, which were previously premium services only obtainable in the "IP Plus" feature
set . Also includes NAT.
IP Voice - Adds VoIP and VoFR.
Advanced Security - Adds IOS/Firewall, IDS, SSH, NAC, and IPSec (DES, 3DES, and AES).
Service Provider Services - Adds Netflow, SSH, BGP, ATM, and VoATM.
Enterprise Base - Adds support for "legacy" L3 protocols such as IPX and Appletalk. Also adds IBM features such as DLSw+, STUN/BSTUN, and RSRB.
The remaining feature sets mostly "add" lower sets together, and do little to no feature addition. A special note on Advanced IP Services:
Advanced IP Services - Beyond merging Advanced Security and SP Services, it adds IPv6.

你可能感兴趣的:(职场,休闲)