路由器之间封装点到点协议：HDLC

 

路由器之间封装点到点协议：HDLC

router 0:
         --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

 

Router>enable 
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#interface serial 0/0
Router(config-if)#ip address 1.1.1.1 255.0.0.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial0/0, changed state to down
Router(config-if)#encapsulation ?
  frame-relay  Frame Relay networks
  hdlc         Serial HDLC synchronous
  ppp          Point-to-Point protocol
Router(config-if)#encapsulation hdlc
Router(config-if)#no shutdown
Router(config-if)#clock ?
  rate  Configure serial interface clock speed
Router(config-if)#clock rate 64000
Router(config-if)#no shutdown
Router(config-if)#
%LINK-5-CHANGED: Interface Serial0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up
Router(config-if)#end
%SYS-5-CONFIG_I: Configured from console by console
Router#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default, U - per-user static route, o - ODR
       P - periodic downloaded static route

Gateway of last resort is not set

C    1.0.0.0/8 is directly connected, Serial0/0
Router#ping 1.1.1.2

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 31/31/32 ms

Router#

 

 

router 1 :

   --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#interface serial 0/0
Router(config-if)#ip address 1.1.1.2 255.0.0.0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial0/0, changed state to up
Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up
Router(config-if)#end
%SYS-5-CONFIG_I: Configured from console by console
Router#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
       * - candidate default, U - per-user static route, o - ODR
       P - periodic downloaded static route

Gateway of last resort is not set

C    1.0.0.0/8 is directly connected, Serial0/0
Router#ping 1.1.1.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 17/28/32 ms

Router#

本文出自 “子逸” 博客，转载请与作者联系！