重新配置Cisco交换机

将一台终端或装有超级终端软件的PC接到交换机的 console口上。终端参数设置如下：
速率：9600bps
检较位：无
数据位：8
停止位：1
流控：无

 

Switch>en
Password:
Switch#
Switch#write erase
Erasing the nvram filesystem will remove all configuration files! Continue? [con
firm]
[OK]
Erase of nvram: complete
Switch#
00:04:43: %SYS-7-NV_BLOCK_INIT: Initalized the geometry of nvram
Switch#reload
Proceed with reload? [confirm]

00:05:06: %SYS-5-RELOAD: Reload requested

C2950 Boot Loader (C2950-HBOOT-M) Version 12.1(11r)EA1, RELEASE SOFTWARE (fc1)
Compiled Mon 22-Jul-02 17:18 by antonino
WS-C2950T-24 starting...
Base ethernet MAC Address: 00:12:43:a4:14:00
Xmodem file system is available.
Initializing Flash...
flashfs[0]: 84 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 7741440
flashfs[0]: Bytes used: 6507520
flashfs[0]: Bytes available: 1233920
flashfs[0]: flashfs fsck took 8 seconds.
...done initializing flash.
Boot Sector Filesystem (bs:) installed, fsid: 3
Parameter Block Filesystem (pb:) installed, fsid: 4
Loading "flash:/c2950-i6q4l2-mz.121-22.EA1.bin"...##############################
################################################################################
#############################################################################

File "flash:/c2950-i6q4l2-mz.121-22.EA1.bin" uncompressed and installed, entry p
oint: 0x80010000
executing...

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA1, RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Mon 12-Jul-04 08:18 by madison
Image text-base: 0x80010000, data-base: 0x8055C000


Initializing flashfs...
flashfs[1]: 84 files, 3 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 7741440
flashfs[1]: Bytes used: 6507520
flashfs[1]: Bytes available: 1233920
flashfs[1]: flashfs fsck took 8 seconds.
flashfs[1]: Initialization complete.
Done initializing flashfs.
POST: System Board Test : Passed
POST: Ethernet Controller Test : Passed
ASIC Initialization Passed

POST: FRONT-END LOOPBACK TEST : Passed
cisco WS-C2950T-24 (RC32300) processor (revision Q0) with 20873K bytes of memory
.
Processor board ID FOC0744Z0WG
Last reset from system-reset
Running Enhanced Image
24 FastEthernet/IEEE 802.3 interface(s)
2 Gigabit Ethernet/IEEE 802.3 interface(s)

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:12:43:A4:14:00
Motherboard assembly number: 73-6114-10
Power supply part number: 34-0965-01
Motherboard serial number: FOC08412CTA
Power supply serial number: DAB0838GVD2
Model revision number: Q0
Motherboard revision number: A0
Model number: WS-C2950T-24
System serial number: FOC0744Z0WG
00:00:16: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
00:00:19: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA1, RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Mon 12-Jul-04 08:18 by madison
00:00:19: %SNMP-5-COLDSTART: SNMP agent on host Switch is undergoing a cold star
t
00:00:23: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to up
00:00:23: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to up
00:00:23: %LINK-3-UPDOWN: Interface FastEthernet0/4, changed state to up
00:00:23: %LINK-3-UPDOWN: Interface FastEthernet0/8, changed state to up
00:00:23: %LINK-3-UPDOWN: Interface FastEthernet0/15, changed state to up
00:00:23: %LINK-3-UPDOWN: Interface FastEthernet0/16, changed state to up
00:00:23: %LINK-3-UPDOWN: Interface FastEthernet0/20, changed state to up
00:00:23: %LINK-3-UPDOWN: Interface FastEthernet0/24, changed state to up
00:00:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, chang
ed state to up
00:00:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, chang
ed state to up
00:00:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, chang
ed state to up
00:00:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/8, chang
ed state to up
00:00:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/15, chan
ged state to up
00:00:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/16, chan
ged state to up
00:00:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/20, chan
ged state to up
00:00:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/24, chan
ged state to up
00:00:55: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state t
o up
00:00:58: AUTOINSTALL: Vlan1 is assigned 172.16.1.45
00:00:58: AUTOINSTALL: Obtain siaddr 172.16.0.1 (as config server)


         --- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: y


At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.


Basic management setup configures only enough connectivity
for management of the system, extended setup will ask you
to configure each interface on the system

Would you like to enter basic management setup? [yes/no]: y
Configuring global parameters:

  Enter host name [Switch]: sw_internet

  The enable secret is a password used to protect access to
  privileged EXEC and configuration modes. This password, after
  entered, becomes encrypted in the configuration.
  Enter enable secret: enablepasswd

  The enable password is used when you do not specify an
  enable secret password, with some older software versions, and
  some boot images.
  Enter enable password: cisco

  The virtual terminal password is used to protect
  access to the router over a network interface.
  Enter virtual terminal password: cisco
  Configure SNMP Network Management? [no]:

Current interface summary

Interface                  IP-Address      OK? Method Status                Prot
ocol
Vlan1                      172.16.1.45     YES other  up                    up

FastEthernet0/1            unassigned      YES unset  down                  down

FastEthernet0/2            unassigned      YES unset  up                    up

FastEthernet0/3            unassigned      YES unset  up                    up

FastEthernet0/4            unassigned      YES unset  up                    up

FastEthernet0/5            unassigned      YES unset  down                  down

FastEthernet0/6            unassigned      YES unset  down                  down

FastEthernet0/7            unassigned      YES unset  down                  down

FastEthernet0/8            unassigned      YES unset  up                    up

FastEthernet0/9            unassigned      YES unset  down                  down

FastEthernet0/10           unassigned      YES unset  down                  down

FastEthernet0/11           unassigned      YES unset  down                  down

FastEthernet0/12           unassigned      YES unset  down                  down

FastEthernet0/13           unassigned      YES unset  down                  down

FastEthernet0/14           unassigned      YES unset  down                  down

FastEthernet0/15           unassigned      YES unset  up                    up

FastEthernet0/16           unassigned      YES unset  up                    up

FastEthernet0/17           unassigned      YES unset  down                  down

FastEthernet0/18           unassigned      YES unset  down                  down

FastEthernet0/19           unassigned      YES unset  down                  down

FastEthernet0/20           unassigned      YES unset  up                    up

FastEthernet0/21           unassigned      YES unset  down                  down

FastEthernet0/22           unassigned      YES unset  down                  down

FastEthernet0/23           unassigned      YES unset  down                  down

FastEthernet0/24           unassigned      YES unset  up                    up

GigabitEthernet0/1         unassigned      YES unset  down                  down

GigabitEthernet0/2         unassigned      YES unset  down                  down


Enter interface name used to connect to the
management network from the above interface summary: vlan1

Configuring interface Vlan1:
  Configure IP on this interface? [yes]:
    IP address for this interface [172.16.1.45]: 172.16.0.3
    Subnet mask for this interface [255.255.0.0] : 255.255.252.0
    Class B network is 172.16.0.0, 22 subnet bits; mask is /22
Would you like to enable as a cluster command switch? [yes/no]: n

The following configuration command script was created:

hostname sw_internet
enable secret 5 $1$Z5Ol$bCjpU9zVIY0H.LJzFeYe8/
enable password cisco
line vty 0 15
password cisco
no snmp-server
!
!
interface Vlan1
no shutdown
ip address 172.16.0.3 255.255.252.0
!
interface FastEthernet0/1
!
interface FastEthernet0/2
!
interface FastEthernet0/3
!
interface FastEthernet0/4
!
 --More--
!
interface FastEthernet0/6
!
interface FastEthernet0/7
!
interface FastEthernet0/8
!
interface FastEthernet0/9
!
interface FastEthernet0/10
!
interface FastEthernet0/11
!
interface FastEthernet0/12
!
interface FastEthernet0/13
!
interface FastEthernet0/14
!
interface FastEthernet0/15
!
interface FastEthernet0/16
!
interface FastEthernet0/17
!
interface FastEthernet0/18
!
interface FastEthernet0/19
!
interface FastEthernet0/20
!
interface FastEthernet0/21
!
interface FastEthernet0/22
!
interface FastEthernet0/23
!
interface FastEthernet0/24
!
interface GigabitEthernet0/1
!
interface GigabitEthernet0/2
!
end


[0] Go to the IOS command prompt without saving this config.
[1] Return back to the setup without saving this config.
[2] Save this configuration to nvram and exit.

Enter your selection [2]:
Building configuration...
[OK]
Use the enabled mode 'configure' command to modify this configuration.




Press RETURN to get started!


sw_internet>