Linux 下Sim卡识别与学习~

项目学习经验：本博文是采用的SCR80读卡器基于USB接口芯片是SCR80_5169，由于realtek官网没有数据手册（本人没有找到）。

只是进行了简单的摸索。

首先：下载Ubuntu 13.04.在虚拟机下安装Ubuntu。之后把必要的驱动安装好。

            需要注意的是，Ubuntu会识别俩个一个是Sim卡一个是Mass USB 需要选择USB的那个，否则读取不正常。

   驱动有libusb libccid ，还有安装服务pcscd，和pcsc-lite+ccid driver 网址：http://pcsclite.alioth.debian.org/

           libusb 和libccid 都可以用synaptic 安装，pcscd 用sudo apt-get install pcscd 即可。

           安装完成后可以用：service pcscd stop/start/restart 进行查看pcscd 服务的开启情况~ 还可以下载pcsc-tools 工具同pcscd 服务下载，安装完成后使用

           pcsc_scan 进行查看sim 卡是否能读取识别。

其次：是SIM卡文件的常识，参考文章：http://www.wuroom.com/post/22/

下面是一个简单的Demo：

主要实现ATR读取和一个APDU的测试，现在可以读取ICCID 和 电话记录，但是更新电话记录还未实现。

#include 
#include 
#include 
#include 
#include 

#include 
#include 
/** error codes from http://msdn.microsoft.com/en-us/library/aa924526.aspx
*/
#define SCARD_S_SUCCESS	 ((LONG)0x00000000) /**< No error was encountered. */
#define SCARD_F_INTERNAL_ERROR	 ((LONG)0x80100001) /**< An internal consistency check failed. */
#define SCARD_E_CANCELLED	 ((LONG)0x80100002) /**< The action was cancelled by an SCardCancel request. */
#define SCARD_E_INVALID_HANDLE	 ((LONG)0x80100003) /**< The supplied handle was invalid. */
#define SCARD_E_INVALID_PARAMETER	((LONG)0x80100004) /**< One or more of the supplied parameters could not be properly interpreted. */
#define SCARD_E_INVALID_TARGET	 ((LONG)0x80100005) /**< Registry startup information is missing or invalid. */
#define SCARD_E_NO_MEMORY	 ((LONG)0x80100006) /**< Not enough memory available to complete this command. */
#define SCARD_F_WAITED_TOO_LONG	 ((LONG)0x80100007) /**< An internal consistency timer has expired. */
#define SCARD_E_INSUFFICIENT_BUFFER	((LONG)0x80100008) /**< The data buffer to receive returned data is too small for the returned data. */
#define SCARD_E_UNKNOWN_READER	 ((LONG)0x80100009) /**< The specified reader name is not recognized. */
#define SCARD_E_TIMEOUT	 ((LONG)0x8010000A) /**< The user-specified timeout value has expired. */
#define SCARD_E_SHARING_VIOLATION	((LONG)0x8010000B) /**< The smart card cannot be accessed because of other connections outstanding. */
#define SCARD_E_NO_SMARTCARD	 ((LONG)0x8010000C) /**< The operation requires a Smart Card, but no Smart Card is currently in the device. */
#define SCARD_E_UNKNOWN_CARD	 ((LONG)0x8010000D) /**< The specified smart card name is not recognized. */
#define SCARD_E_CANT_DISPOSE	 ((LONG)0x8010000E) /**< The system could not dispose of the media in the requested manner. */
#define SCARD_E_PROTO_MISMATCH	 ((LONG)0x8010000F) /**< The requested protocols are incompatible with the protocol currently in use with the smart card. */
#define SCARD_E_NOT_READY	 ((LONG)0x80100010) /**< The reader or smart card is not ready to accept commands. */
#define SCARD_E_INVALID_VALUE	 ((LONG)0x80100011) /**< One or more of the supplied parameters values could not be properly interpreted. */
#define SCARD_E_SYSTEM_CANCELLED	((LONG)0x80100012) /**< The action was cancelled by the system, presumably to log off or shut down. */
#define SCARD_F_COMM_ERROR	 ((LONG)0x80100013) /**< An internal communications error has been detected. */
#define SCARD_F_UNKNOWN_ERROR	 ((LONG)0x80100014) /**< An internal error has been detected, but the source is unknown. */
#define SCARD_E_INVALID_ATR	 ((LONG)0x80100015) /**< An ATR obtained from the registry is not a valid ATR string. */
#define SCARD_E_NOT_TRANSACTED	 ((LONG)0x80100016) /**< An attempt was made to end a non-existent transaction. */
#define SCARD_E_READER_UNAVAILABLE	((LONG)0x80100017) /**< The specified reader is not currently available for use. */
#define SCARD_P_SHUTDOWN	 ((LONG)0x80100018) /**< The operation has been aborted to allow the server application to exit. */
#define SCARD_E_PCI_TOO_SMALL	 ((LONG)0x80100019) /**< The PCI Receive buffer was too small. */
#define SCARD_E_READER_UNSUPPORTED	((LONG)0x8010001A) /**< The reader driver does not meet minimal requirements for support. */
#define SCARD_E_DUPLICATE_READER	((LONG)0x8010001B) /**< The reader driver did not produce a unique reader name. */
#define SCARD_E_CARD_UNSUPPORTED	((LONG)0x8010001C) /**< The smart card does not meet minimal requirements for support. */
#define SCARD_E_NO_SERVICE	 ((LONG)0x8010001D) /**< The Smart card resource manager is not running. */
#define SCARD_E_SERVICE_STOPPED	 ((LONG)0x8010001E) /**< The Smart card resource manager has shut down. */
#define SCARD_E_UNEXPECTED	 ((LONG)0x8010001F) /**< An unexpected card error has occurred. */
#define SCARD_E_UNSUPPORTED_FEATURE	((LONG)0x8010001F) /**< This smart card does not support the requested feature. */
#define SCARD_E_ICC_INSTALLATION	((LONG)0x80100020) /**< No primary provider can be found for the smart card. */
#define SCARD_E_ICC_CREATEORDER	 ((LONG)0x80100021) /**< The requested order of object creation is not supported. */
/* #define SCARD_E_UNSUPPORTED_FEATURE	((LONG)0x80100022) / **< This smart card does not support the requested feature. */
#define SCARD_E_DIR_NOT_FOUND	 ((LONG)0x80100023) /**< The identified directory does not exist in the smart card. */
#define SCARD_E_FILE_NOT_FOUND	 ((LONG)0x80100024) /**< The identified file does not exist in the smart card. */
#define SCARD_E_NO_DIR	 ((LONG)0x80100025) /**< The supplied path does not represent a smart card directory. */
#define SCARD_E_NO_FILE	 ((LONG)0x80100026) /**< The supplied path does not represent a smart card file. */
#define SCARD_E_NO_ACCESS	 ((LONG)0x80100027) /**< Access is denied to this file. */
#define SCARD_E_WRITE_TOO_MANY	 ((LONG)0x80100028) /**< The smart card does not have enough memory to store the information. */
#define SCARD_E_BAD_SEEK	 ((LONG)0x80100029) /**< There was an error trying to set the smart card file object pointer. */
#define SCARD_E_INVALID_CHV	 ((LONG)0x8010002A) /**< The supplied PIN is incorrect. */
#define SCARD_E_UNKNOWN_RES_MNG	 ((LONG)0x8010002B) /**< An unrecognized error code was returned from a layered component. */
#define SCARD_E_NO_SUCH_CERTIFICATE	((LONG)0x8010002C) /**< The requested certificate does not exist. */
#define SCARD_E_CERTIFICATE_UNAVAILABLE	((LONG)0x8010002D) /**< The requested certificate could not be obtained. */
#define SCARD_E_NO_READERS_AVAILABLE ((LONG)0x8010002E) /**< Cannot find a smart card reader. */
#define SCARD_E_COMM_DATA_LOST	 ((LONG)0x8010002F) /**< A communications error with the smart card has been detected. Retry the operation. */
#define SCARD_E_NO_KEY_CONTAINER	((LONG)0x80100030) /**< The requested key container does not exist on the smart card. */
#define SCARD_E_SERVER_TOO_BUSY	 ((LONG)0x80100031) /**< The Smart Card Resource Manager is too busy to complete this operation. */

#define SCARD_W_UNSUPPORTED_CARD	((LONG)0x80100065) /**< The reader cannot communicate with the card, due to ATR string configuration conflicts. */
#define SCARD_W_UNRESPONSIVE_CARD	((LONG)0x80100066) /**< The smart card is not responding to a reset. */
#define SCARD_W_UNPOWERED_CARD	 ((LONG)0x80100067) /**< Power has been removed from the smart card, so that further communication is not possible. */
#define SCARD_W_RESET_CARD	 ((LONG)0x80100068) /**< The smart card has been reset, so any shared state information is invalid. */
#define SCARD_W_REMOVED_CARD	 ((LONG)0x80100069) /**< The smart card has been removed, so further communication is not possible. */

#define SCARD_W_SECURITY_VIOLATION	((LONG)0x8010006A) /**< Access was denied because of a security violation. */
#define SCARD_W_WRONG_CHV	 ((LONG)0x8010006B) /**< The card cannot be accessed because the wrong PIN was presented. */
#define SCARD_W_CHV_BLOCKED	 ((LONG)0x8010006C) /**< The card cannot be accessed because the maximum number of PIN entry attempts has been reached. */
#define SCARD_W_EOF	 ((LONG)0x8010006D) /**< The end of the smart card file has been reached. */
#define SCARD_W_CANCELLED_BY_USER	((LONG)0x8010006E) /**< The user pressed "Cancel" on a Smart Card Selection Dialog. */
#define SCARD_W_CARD_NOT_AUTHENTICATED	((LONG)0x8010006F) /**< No PIN was presented to the smart card. */

#define SCARD_AUTOALLOCATE (DWORD)(-1)	/**< see SCardFreeMemory() */
#define SCARD_SCOPE_USER	 0x0000	/**< Scope in user space */
#define SCARD_SCOPE_TERMINAL	 0x0001	/**< Scope in terminal */
#define SCARD_SCOPE_SYSTEM	 0x0002	/**< Scope in system */

#define SCARD_PROTOCOL_UNDEFINED	0x0000	/**< protocol not set */
#define SCARD_PROTOCOL_UNSET SCARD_PROTOCOL_UNDEFINED	/* backward compat */
#define SCARD_PROTOCOL_T0	 0x0001	/**< T=0 active protocol. */
#define SCARD_PROTOCOL_T1	 0x0002	/**< T=1 active protocol. */
#define SCARD_PROTOCOL_RAW	 0x0004	/**< Raw active protocol. */
#define SCARD_PROTOCOL_T15	 0x0008	/**< T=15 protocol. */

#define SCARD_PROTOCOL_ANY	 (SCARD_PROTOCOL_T0|SCARD_PROTOCOL_T1)	/**< IFD determines prot. */

#define SCARD_SHARE_EXCLUSIVE	 0x0001	/**< Exclusive mode only */
#define SCARD_SHARE_SHARED	 0x0002	/**< Shared mode only */
#define SCARD_SHARE_DIRECT	 0x0003	/**< Raw mode only */

#define SCARD_LEAVE_CARD	 0x0000	/**< Do nothing on close */
#define SCARD_RESET_CARD	 0x0001	/**< Reset on close */
#define SCARD_UNPOWER_CARD	 0x0002	/**< Power down on close */
#define SCARD_EJECT_CARD	 0x0003	/**< Eject on close */

#define SCARD_UNKNOWN	 0x0001	/**< Unknown state */
#define SCARD_ABSENT	 0x0002	/**< Card is absent */
#define SCARD_PRESENT	 0x0004	/**< Card is present */
#define SCARD_SWALLOWED	 0x0008	/**< Card not powered */
#define SCARD_POWERED	 0x0010	/**< Card is powered */
#define SCARD_NEGOTIABLE	 0x0020	/**< Ready for PTS */
#define SCARD_SPECIFIC	 0x0040	/**< PTS has been set */

#define SCARD_STATE_UNAWARE	 0x0000	/**< App wants status */
#define SCARD_STATE_IGNORE	 0x0001	/**< Ignore this reader */
#define SCARD_STATE_CHANGED	 0x0002	/**< State has changed */
#define SCARD_STATE_UNKNOWN	 0x0004	/**< Reader unknown */
#define SCARD_STATE_UNAVAILABLE	 0x0008	/**< Status unavailable */
#define SCARD_STATE_EMPTY	 0x0010	/**< Card removed */
#define SCARD_STATE_PRESENT	 0x0020	/**< Card inserted */
#define SCARD_STATE_ATRMATCH	 0x0040	/**< ATR matches card */
#define SCARD_STATE_EXCLUSIVE	 0x0080	/**< Exclusive Mode */
#define SCARD_STATE_INUSE	 0x0100	/**< Shared Mode */
#define SCARD_STATE_MUTE	 0x0200	/**< Unresponsive card */
#define SCARD_STATE_UNPOWERED	 0x0400	/**< Unpowered card */

#ifndef INFINITE
#define INFINITE	 0xFFFFFFFF	/**< Infinite timeout */
#endif
#define MAX_ATR_SIZE	 33	/**< Maximum ATR size */
#define MAX_READERNAME	 100

extern const SCARD_IO_REQUEST g_rgSCardT0Pci, g_rgSCardT1Pci, g_rgSCardRawPci;
#define SCARD_PCI_T0	(&g_rgSCardT0Pci) /**< protocol control information (PCI) for T=0 */
#define SCARD_PCI_T1	(&g_rgSCardT1Pci) /**< protocol control information (PCI) for T=1 */
#define SCARD_PCI_RAW	(&g_rgSCardRawPci) /**< protocol control information (PCI) for RAW protocol */


#ifndef TRUE
#define TRUE 1
#define FALSE 0
#endif


int main(int argc, char *argv[])
{
	LONG rv;
	SCARDCONTEXT hContext;
	DWORD dwReaders;
	LPSTR mszReaders = NULL;
	char *ptr, **readers = NULL;
	int nbReaders;
	SCARDHANDLE hCard;
	DWORD dwActiveProtocol, dwReaderLen, dwState, dwProt, dwAtrLen;
	BYTE pbAtr[MAX_ATR_SIZE] = "";
	char pbReader[MAX_READERNAME] = "";
	int reader_nb;
	unsigned int i;
	const SCARD_IO_REQUEST *pioSendPci;
	SCARD_IO_REQUEST pioRecvPci;
	BYTE pbRecvBuffer[100];
	BYTE pbSendBuffer[] = { 0xa0, 0xA4, 0x00, 0x00, 0x02, 0x3F, 0x00 };
	BYTE pbSendBuffer1[] = { 0xa0, 0xA4, 0x00, 0x00, 0x02, 0x2F, 0xe2 };
	BYTE pbSendBuffer2[] = { 0xa0, 0xb0, 0x00, 0x00, 0x0a };
	#define MF_3f00 pbSendBuffer
	#define EF_2fe2 pbSendBuffer1
	#define EF_read pbSendBuffer2
	
	DWORD dwSendLength, dwRecvLength;

	printf("PC/SC sample iccid read code\n");

	rv = SCardEstablishContext(SCARD_SCOPE_SYSTEM, NULL, NULL, &hContext);
	if (rv != SCARD_S_SUCCESS)
	{
		printf("SCardEstablishContext: Cannot Connect to Resource Manager %lX\n", rv);
		while(1);
	}
	

	/* Retrieve the available readers list. */
	dwReaders = SCARD_AUTOALLOCATE;
	rv = SCardListReaders(hContext, NULL, (LPSTR)&mszReaders, &dwReaders);
	

	/* Extract readers from the null separated string and get the total
	* number of readers */
	nbReaders = 0;
	ptr = mszReaders;
	while (*ptr != '\0')
	{
		ptr += strlen(ptr)+1;
		nbReaders++;
	}
	
	if (nbReaders == 0)
	{
		printf("No reader found\n");
		while(1);
	}
	
	/* allocate the readers table */
	readers = calloc(nbReaders, sizeof(char *));
	if (NULL == readers)
	{
		printf("Not enough memory for readers[]\n");
		while(1);
	}
	
	/* fill the readers table */
	nbReaders = 0;
	ptr = mszReaders;
	while (*ptr != '\0')
	{
		printf("%d: %s\n", nbReaders, ptr);
		readers[nbReaders] = ptr;
		ptr += strlen(ptr)+1;
		nbReaders++;
	}
	
	if (argc > 1)
	{
		reader_nb = atoi(argv[1]);
		if (reader_nb < 0 || reader_nb >= nbReaders)
		{
			printf("Wrong reader index: %d\n", reader_nb);
			while(1);
		}
	}
	else
		reader_nb = 0;
	
	
	/* connect to a card */
	dwActiveProtocol = -1;
	
	rv = SCardConnect(hContext, readers[reader_nb], SCARD_SHARE_SHARED,
	SCARD_PROTOCOL_T0 | SCARD_PROTOCOL_T1, &hCard, &dwActiveProtocol);
	printf(" Protocol: %ld\n", dwActiveProtocol-1);//T0 T1 1,2 
	
	
	/* get card status */
	dwAtrLen = sizeof(pbAtr);
	dwReaderLen = sizeof(pbReader);
	rv = SCardStatus(hCard, /*NULL*/ pbReader, &dwReaderLen, &dwState, &dwProt,pbAtr, &dwAtrLen);
	printf(" Reader: %s (length %ld bytes)\n", pbReader, dwReaderLen);
	printf(" State: 0x%lX\n", dwState);
	printf(" Prot: %ld\n", dwProt);
	printf(" ATR (length %ld bytes):", dwAtrLen);
	for (i=0; i