CCNA--LAB-11:配置单臂路由(企业经典案例)

什么是单臂路由 : 为什么要用到单臂路由。 VLAN （虚拟局域网）技术是路由交换中非常基础的技术。在网络管理实践中，通过在交换机上划分适当数目的 vlan ，不仅能有效隔离广播风暴，还能提高网络安全系数及网络带宽的利用效率。划分 vlan 之后， vlan 与 vlan 之间是不能通信的， 要想使不同 VLAN 里的主机互访就得使用 VLAN 间路由技术。在考虑成本的情况下我们一般选择单臂路由，单臂路由需要一台交换机和一台路由器来共同实现。

 

 

拓扑如下：

 

实验目的：接口信息以及 IP 地址规划如拓扑所示， PC1 ―― PC3 分别属于 VLAN1 ―― VLAN3 ，

运用单臂路由与 NAT 的结合， 最终使得用户之间能够互相访问，使企业内部全部能够访问因特网。

 

 

具体配置：

 

R1：
 
Router>
Router>en
Router#conf t
Router(config)#hostname R1
R1(config)#interface f0/0
R1(config-if)#no sh      --首先把物理接口激活，其它子接口就不用再激活
R1(config)#interface f0/0.1    --进入子接口模式
R1(config-subif)#encapsulation dot1Q 1     --对VLAN1进行封装DOT1Q
R1(config-subif)#ip address 192.168.1.254 255.255.255.0
R1(config-subif)#exit
R1(config)#interface f0/0.2     --进入子接口模式
R1(config-subif)#encapsulation dot1Q 2     --对VLAN2进行封装DOT1Q
R1(config-subif)#ip address 192.168.2.254 255.255.255.0
R1(config-subif)#exit
R1(config)#interface f0/0.3     --进入子接口模式
R1(config-subif)#encapsulation dot1Q 3     --对VLAN3进行封装DOT1Q
R1(config-subif)#ip address 192.168.3.254 255.255.255.0
R1(config-subif)#exit
R1(config)#interface f0/1
R1(config-if)#ip address 218.87.18.1 255.255.255.0
R1(config-if)#no sh
R1(config-if)#exit
R1(config)#access-list 1 permit 192.168.1.0 0.0.0.255     --定义允许的流量
R1(config)#access-list 1 permit 192.168.2.0 0.0.0.255
R1(config)#access-list 1 permit 192.168.3.0 0.0.0.255
R1(config)#ip nat inside source list 1 interface f0/1 overload
--定义符合访问控制列表1的流量向F0/1口转发
R1(config)#interface f0/0.1
R1(config-subif)#ip nat inside   --定义内部接口
R1(config-subif)#interface f0/0.2
R1(config-subif)#ip nat inside
R1(config-subif)#interface f0/0.3
R1(config-subif)#ip nat inside
R1(config-subif)#exit
R1(config-if)#interface f0/1
R1(config-if)#ip nat outside    --定义外部接口
R1(config-if)#exit
R1(config)#ip route 0.0.0.0 0.0.0.0 218.87.18.2    --默认路由指向ISP
R1(config-if)#end
R1#
 
 
 
 
SW1：
 
Switch>
Switch>en
Switch#conf t
Switch(config)#hostname SW1
SW1(config)#vlan 2     --创建VLAN2
SW1(config-vlan)#exit
SW1(config)#vlan 3     --创建VLAN3
SW1(config-vlan)#exit
SW1(config)#interface f0/2
SW1(config-if)#switchport mode access     --端口模式为ACCESS
SW1(config-if)#switchport access vlan 2    --把当前端口加入到VLAN2
SW1(config-if)#no sh
SW1(config-if)#exit
SW1(config)#interface f0/3
SW1(config-if)#switchport mode access     --端口模式为ACCESS
SW1(config-if)#switchport access vlan 3    --把当前端口加入到VLAN3
SW1(config-if)#exit
SW1(config)#interface f0/24
SW1(config)#switchport trunk encapsulation dot1q    --把接口封装为DOT1Q
SW1(config-if)#switchport mode trunk      --接口模式为TRUNK（中继）
SW1(config-if)#no sh
SW1(config-if)#end
SW1#
 
 

ISP:
 
Router>
Router>en
Router#conf t
Router(config)#hostname ISP
ISP(config)#interface f0/1
ISP(config-if)#ip address 218.87.18.2 255.255.255.0
ISP(config-if)#no sh
ISP(config-if)#end
ISP#
 
 
 
3台PC上分别做验证：
 
PC1:
 
PC>ipconfig
 
IP Address......................: 192.168.1.1
Subnet Mask.....................: 255.255.255.0
Default Gateway.................: 192.168.1.254
 
 
PC>ping 218.87.18.2
 
Pinging 218.87.18.2 with 32 bytes of data:
 
Reply from 218.87.18.2: bytes=32 time=73ms TTL=254
Reply from 218.87.18.2: bytes=32 time=112ms TTL=254
Reply from 218.87.18.2: bytes=32 time=52ms TTL=254
Reply from 218.87.18.2: bytes=32 time=70ms TTL=254
 
Ping statistics for 218.87.18.2:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 52ms, Maximum = 112ms, Average = 76ms
 
PC>
 

PC>ping 192.168.2.1

Pinging 192.168.2.1 with 32 bytes of data:
 
Reply from 192.168.2.1: bytes=32 time=73ms TTL=254
Reply from 192.168.2.1: bytes=32 time=112ms TTL=254
Reply from 192.168.2.1: bytes=32 time=52ms TTL=254
Reply from 192.168.2.1: bytes=32 time=70ms TTL=254
 
Ping statistics for 192.168.2.1:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 52ms, Maximum = 112ms, Average = 76ms
 
PC>

PC>ping 192.168.3.1
 
Pinging 192.1683.1 with 32 bytes of data:
 
Reply from 192.168.3.1: bytes=32 time=73ms TTL=254
Reply from 192.168.3.1: bytes=32 time=112ms TTL=254
Reply from 192.168.3.1: bytes=32 time=52ms TTL=254
Reply from 192.168.3.1: bytes=32 time=70ms TTL=254
 
Ping statistics for 192.168.3.1:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 52ms, Maximum = 112ms, Average = 76ms
 
PC>

-------------------------------------------------------------------------------------

 

PC2:
 
PC>ipconfig
 
IP Address......................: 192.168.2.1
Subnet Mask.....................: 255.255.255.0
Default Gateway.................: 192.168.2.254
 
PC>ping 218.87.18.2
 
Pinging 218.87.18.2 with 32 bytes of data:
 
Reply from 218.87.18.2: bytes=32 time=39ms TTL=254
Reply from 218.87.18.2: bytes=32 time=44ms TTL=254
Reply from 218.87.18.2: bytes=32 time=58ms TTL=254
Reply from 218.87.18.2: bytes=32 time=29ms TTL=254
 
Ping statistics for 218.87.18.2:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 29ms, Maximum = 58ms, Average = 42ms
 
PC>
 

 

-------------------------------------------------------------------------------------
 
PC3:
 
PC>ipconfig
 
IP Address......................: 192.168.3.1
Subnet Mask.....................: 255.255.255.0
Default Gateway.................: 192.168.3.254
 
PC>ping 218.87.18.2
 
Pinging 218.87.18.2 with 32 bytes of data:
 
Reply from 218.87.18.2: bytes=32 time=83ms TTL=254
Reply from 218.87.18.2: bytes=32 time=71ms TTL=254
Reply from 218.87.18.2: bytes=32 time=42ms TTL=254
Reply from 218.87.18.2: bytes=32 time=44ms TTL=254
 
Ping statistics for 218.87.18.2:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 42ms, Maximum = 83ms, Average = 60ms
 
PC>
 
 
总结：
 
本实验与实际中小企业网络非常相似，部署单臂路由既节省了成本，又提高了工作效率.